User manual MAKITA BFL300F

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA BFL300F. We hope that this MAKITA BFL300F user guide will be useful to you.


MAKITA BFL300F : Download the complete user guide (186 Ko)

You may also download the following manuals related to this product:

   MAKITA BFL300F (650 ko)
   MAKITA BFL300F (650 ko)
   MAKITA BFL300F (650 ko)
   MAKITA BFL300F (650 ko)
   MAKITA BFL300F (650 ko)
   MAKITA BFL300F (650 ko)
   MAKITA BFL300F (650 ko)
   MAKITA BFL300F (650 ko)
   MAKITA BFL300F (650 ko)
   MAKITA BFL300F (650 ko)
   MAKITA BFL300F (650 ko)
   MAKITA BFL300F (650 ko)
   MAKITA BFL300F (650 ko)

Manual abstract: user guide MAKITA BFL300F

Detailed instructions for use are in the User's Guide.

[. . . ] If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. [. . . ] Changing the direction of rotation before the tool stops may damage the tool. ⷠWhen not operating the tool, always set the reversing switch lever to the neutral position. this tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. Always stop tool operation and charge the battery cartridge when you notice less tool power. Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months. The light automatically goes out 10 seconds after the switch trigger is released. nOTE: · Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. For approximately one second after auto-stop fastening, the tool does not start even if the switch trigger is pulled. Warning against insufficient fastening Warning for battery cartridge capacity Checking the remaining battery capacity, Auto-stop Check the LED indicator, light and beeper operation Insufficient fastening has been performed when the switch trigger has Lights up in released before reaching the preset fas- red. This indicates the appropriate time to replace the battery cartridge when the battery power becomes low. This function works to check the proper operation of the LED indicator, light and beeper when a battery cartridge has been inserted into the tool. This function works when an abnormal drop of the battery voltage occurs for some reason and the tool stops. This function works if the temperature of the controller or motor increases to a high level and the tool stops. This function works to avoid the tool's immediate start upon insertion of battery cartridge into the tool with the switch trigger being pulled. Rotate the ring in the front of the tool by hand so that a hole can be seen below the ring. [. . . ] To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centres, always using Makita replacement parts. These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA BFL300F




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA BFL300F will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.