User manual MAKITA BPJ180

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA BPJ180. We hope that this MAKITA BPJ180 user guide will be useful to you.


MAKITA BPJ180 : Download the complete user guide (1549 Ko)

Manual abstract: user guide MAKITA BPJ180

Detailed instructions for use are in the User's Guide.

[. . . ] Always be sure that the tool is switched off and the battery cartridge is removed before making any adjustments or replacing the blade. WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. Always stop tool operation and charge the battery cartridge when you notice less tool power. [. . . ] To remove the angle guide, loosen the lock lever and turn the knob clockwise until it comes out of the upper end of the fence. 5 & 6) NOTE: • Remove the angle guide according to the need of your work when using the tool with the angle of the fence adjusted to other than 0°. When you need to use the angle guide under the above condition, be sure to adjust the depth of groove to get a proper depth. 7 The angle of the fence can be adjusted between 0° and 90° (positive stops at 0°, 45° and 90°). To adjust the angle, loosen the lock lever and tilt the fence until the pointer points to the desired graduation on the angle scale. When the fence is set at 90°, both the distance from the center of the blade thickness to the fence and the distance from the center of the blade thickness to the bottom of the base are 10 mm. 11) CAUTION: • When installing the plate joiner blade, mount the inner flange with the side marked “22” facing toward you. Push the shaft lock and loosen the lock nut using the lock nut wrench. Close the blade cover and tighten the clamp screw to secure the blade cover. CAUTION: • Use only Makita lock nut wrench provided to remove or install the blade. €¢ Always check the depth of groove after replacing the blade. 9) CAUTION: • Before installing the battery cartridge into the tool, always check to see that the slide switch actuates properly and returns to the “OFF” position when the rear of the slide switch is depressed. €¢ Switch can be locked in “ON” position for ease of operator comfort during extended use. apply caution when locking tool in “ON” position and maintain firm grasp on tool. To start the tool, slide the slide switch toward the “I (ON)” position. For continuous operation, press the front of the slide switch to lock it. To stop the tool, press the rear of the slide switch, then slide it toward the “O (OFF)” position. When the dust bag is about half full, switch off and remove the battery cartridge. Remove the dust bag from the tool and pull the bag’s fastener out. NOTE: • If you connect a Makita vacuum cleaner to your plate joiner, more efficient and cleaner operations can be performed. [. . . ] If you do not need to center the blade in the board thickness, proceed as follows: For Corner Joint, Miter Joint, Frame Joint and EdgeTo-Edge Joint only • Remove the angle guide from the tool. For T-Butt Joint only • Fit the two workpieces together as they will appear in the finished joint position. • Follow the steps 2 , 4 , 6 , 7 , 8 and 11 described above. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA BPJ180




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA BPJ180 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.