User manual MAKITA BTP141

[. . . ] Be sure that you understand their meaning before use. . . . . . . . . . . . . . . . . . . Only for EU countries Do not dispose of electric equipment together with household waste material!In observance of European Directive 2002/96/EC on waste electric and electronic equipment and its implementation in accordance with national law, electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. Intended use The tool is intended for impact screw driving in wood and for impact drilling in brick, concrete and stone as well as for drilling and screw driving without impact in wood, metal, ceramic and plastic, . For Model BTP141 For European countries only Noise and Vibration The typical A-weighted noise levels are sound pressure level: 89 dB (A) sound power level: 100 dB (A) Uncertainty: 3 dB ­ Wear ear protection. ­ The typical weighted root mean square acceleration value is 9 m/s2. [. . . ] Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. Be careful not to drop or strike battery. SAVE THESE INSTRUCTIONS. Tips for maintaining maximum battery life 1. Always stop tool operation and charge the battery cartridge when you notice less tool power. Charge the battery cartridge with room temperature at 10°C - 40°C (50°F - 104°F). Let a hot battery cartridge cool down before charging it. 2. SAVE THESE INSTRUCTIONS. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. ENC007-2 3. IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE 1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. Sleeve 2 004347 To install the bit, pull the sleeve in the direction of the arrow and insert the bit-piece and bit into the sleeve as far as it will go. The bit-piece should be inserted into the sleeve with its pointed end facing in. To remove the bit, pull the sleeve in the direction of the arrow and pull the bit out firmly. Sleeve 2 3 · If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the bit will not be secured. In this case, try re-inserting the bit according to the instructions above. 006251 Hook (Accessory) CAUTION: When installing the hook, tighten the screw firmly. Failure to do so may cause the breakage of the tool or personal injury. To install the hook, insert it into a groove in the tool housing on either side and then secure it with a screw. Groove 9 OPERATION · CAUTION: Always insert the battery cartridge all the way until it locks in place. If you can see the red part on the upper side of the button, it is not locked completely. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. Impact driver operation When driving wood screws or bolts. Screwdriving 007411 Hold the tool firmly and place the point of the driver bit in the screw head. [. . . ] By repeating this several times, the hole will be cleaned out and normal drilling may be resumed. · 11 · CAUTION: If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. Screwdriving operation CAUTION: · Adjust the adjusting ring to the proper torque level for your work. Place the point of the driver bit in the screw head and apply pressure to the tool. CAUTION: Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. [. . . ]