User manual MAKITA DPC7301

[. . . ] For the components listed under PARTS COVERED, the service dealer authorized by MAKITA will, at no cost to you, make the necessary diagnosis, repair, or replacement necessary to ensure that the engine complies with applicable U. EMISSION COMPONENT DEFECT WARRANTY PERIOD The warranty period for this engine begins on the date of sale to the initial purchaser and continues for a period of 2 years. PARTS COVERED Listed below are the parts covered by the Emission Components Defect Warranty. Some of the parts listed below may require scheduled maintenance and are warranted up to the first scheduled replacement point for that part. [. . . ] , always make sure to plan the direction and sequence of cuts in such a way that the disc does not get jammed by the cut-off piece, and that no persons can be injured by falling pieces. Always turn off the Power Cut when transporting it or moving it from place to place on a site (26). Carry the unit only by the tubular (middle) handle with the cutting disc pointing behind you (26). ) When moving the Power Cut over longer distances, use a wheelbarrow or wagon. When transporting the Power Cut in a vehicle, make sure it is securely positioned in such a way that no fuel can leak out. Always remove the cutting disc before transporting the unit in a vehicle. Before long-term storage and before shipping the Power Cut, follow the instructions in the chapter on "Periodic care and maintenance". When putting cutting discs in storage, be careful to: Clean and dry them well. avoid dampness , freezing temperatures , direct sunshine , high temperatures and temperature fluctuations , as these can cause breakage and splintering. Always check new cutting discs or cutting discs that have been in storage to make sure that they are free of defects and before the first cut test-run the tool at top speed for at least 60 seconds. Keep body parts and people well away out of range of the direction of the cutting disc during this test. NOTE: The two fastening nuts (11) must be loosened before tightening the V-belt or checking the tension. To increase the belt tension, turn the tightening screw (12) to the right (clockwise) with the combination wrench included with the Power Cut. IMPORTANT: After tightening/inspection, make certain to tighten the fastening nuts (11) (30 ± 2 Nm). CAUTION: Before doing any work on the Power Cut, always switch off the engine and disconnect the spark plug cap!NOTE: When using a protective hood for a maximum disk diameter of 300 mm (12"), always shorten hose (1) to 180 mm (7"). To do this unscrew sleeve (2) and carefully pull tube (1) off coupling (3) and cut to 180 mm. Then push the tube end back over the coupling and tighten the sleeve all the way. Push clamp (H/8) around the front grip (H/9) and fasten with the bolt and square nut. Pull the quick-release coupling (H/10) from the water connection and connect it to the 1/2" supply line (4). Tube routing with the cutting assembly in the middle position, see Fig. Tube routing with the cutting assembly in the outside position, see Fig. [. . . ] Users of the Power Cut must not perform any maintenance work not described in this Instruction Manual. Page General Entire Power Cut Cutting disc Clutch Protection hood Before each start Cutting disc V-belt Protective hood Combination switch, Safety locking button, Throttle lever Tank cap Every day Air filter Idle speed Extreme dust Every week Starter housing Starter cable V-belt Air filter insert Spark plug Muffler Every 3 months Suction head Fuel tank Annually Storage Entire Power Cut Entire Power Cut Cutting disc Fuel tank Carburetor Clean exterior, check for damage. Clean, Check position (impact plate) Inspect for damage and make sure the cutting wheel is right for the job Check V-belt tension Adjust position Functional check Functional check Functional check Check for tightness Clean, (poss. More often), replace foam pre-filter after 20 hours of operation Check (cutting disc must not turn on idle) Clean filter insert (paper cartridge) Clean to ensure proper air cooling Check for damage Check V-belt tension, inspect for damage and wear Clean, replace after 100 operating hours Check and replace if necessary Check tightness of mounting Replace Clean Check at an authorized service center Clean exterior, check for damage. [. . . ]