User manual MAKITA GA5030KSP2

[. . . ] Shaft lock Switch lever Wheel guard Screw Bearing box Lever Lock nut Depressed center grinding wheel/ Multi-disc 9. Inhalation vent SPECIFICATIONS Model Depressed center wheel diameter Spindle thread Rated speed (n)/No load speed (n0) Overall length Net weight Safety class GA4030 100 mm M10 11, 000 min-1 266 mm 1. 8 kg • Due to our continuing program of research and development, the specifications herein are subject to change without notice. € Weight according to EPTA-Procedure 01/2003 Symbols END202-6 The following show the symbols used for the equipment. [. . . ] Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel. F) Use extra caution when making a “pocket cut” into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback. Safety Warnings Specific for Sanding Operations: a) Do not use excessively oversized sanding disc paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback. Safety Warnings Specific for Wire Brushing Operations: a) Be aware that wire bristles are thrown by the brush even during ordinary operation. B) If the use of a guard is recommended for wire brushing, do not allow interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work load and centrifugal forces. When using depressed center grinding wheels, be sure to use only fiberglass-reinforced wheels. Be careful not to damage the spindle, the flange (especially the installing surface) or the lock nut. Make sure the wheel is not contacting the workpiece before the switch is turned on. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel. Hold the tool so that sparks fly away from you and other persons or flammable materials. Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. Always be sure that the tool is switched off and unplugged or that the battery cartridge is removed before carrying out any work on the tool. Observe the instructions of the manufacturer for correct mounting and use of wheels. Do not use separate reducing bushings or adaptors to adapt large hole abrasive wheels. For tools intended to be fitted with threaded hole wheel, ensure that the thread in the wheel is long enough to accept the spindle length. Pay attention that the wheel continues to rotate after the tool is switched off. If working place is extremely hot and humid, or badly polluted by conductive dust, use a shortcircuit breaker (30 mA) to assure operator safety. Ensure that ventilation openings are kept clear when working in dusty conditions. If it should become necessary to clear dust, first disconnect the tool from the mains supply (use non metallic objects) and avoid damaging internal parts. [. . . ] If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. € Wheel guard (Wheel cover) For depressed center wheel/Multi disc • Wheel guard (Wheel cover) For abrasive cut-off wheel/ diamond wheel • Depressed center wheels • Abrasive cut-off wheels • Multi discs • Diamond wheels • Wire cup brushes • Wire bevel brush 85 • Abrasive discs • Inner flange • Lock nut For depressed center wheel/abrasive cut-off wheel/multi disc/diamond wheel • Lock nut For abrasive disc • Lock nut wrench • Side grip 8 of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). For Model GA5030 Noise ENG102-3 The typical A-weighted noise level determined according to EN60745: Sound pressure level (LpA): 85 dB (A) Sound power level (LWA): 96 dB (A) Uncertainty (K): 3 dB (A) Wear ear protection. 5 m/s2 The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another. [. . . ]