User manual MAKITA HM1317CB

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA HM1317CB. We hope that this MAKITA HM1317CB user guide will be useful to you.


MAKITA HM1317CB : Download the complete user guide (1061 Ko)

You may also download the following manuals related to this product:

   MAKITA HM1317CB (1119 ko)
   MAKITA HM1317CB (1119 ko)
   MAKITA HM1317CB (1119 ko)
   MAKITA HM1317CB (1119 ko)
   MAKITA HM1317CB (1119 ko)
   MAKITA HM1317CB (1119 ko)
   MAKITA HM1317CB (1119 ko)
   MAKITA HM1317CB (1119 ko)
   MAKITA HM1317CB (1119 ko)
   MAKITA HM1317CB (1119 ko)
   MAKITA HM1317CB (1119 ko)
   MAKITA HM1317CB (1119 ko)
   MAKITA HM1317CB (1119 ko)
   MAKITA HM1317CB ANNEXE 75 (1119 ko)
   MAKITA HM1317CB ANNEXE 519 (1119 ko)
   MAKITA HM1317CB PARTS (1315 ko)
   MAKITA HM1317CB ANNEXE 88 (1119 ko)
   MAKITA HM1317CB PARTS LIST (1314 ko)
   MAKITA HM1317CB ANNEXE 365 (520 ko)
   MAKITA HM1317CB PARTS LIST 11-2009 (1315 ko)

Manual abstract: user guide MAKITA HM1317CB

Detailed instructions for use are in the User's Guide.

[. . . ] If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. [. . . ] Table 1 shows the correct size to use depending on cord length and nameplate ampere rating. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. it is also highly recommended that you wear a dust mask and thickly padded gloves. In cold weather or when the tool has not been used for a long time, let the tool warm up for a while by operating it under no load. Do not touch the bit or parts close to the bit immediately after operation; they may be extremely hot and could burn your skin. CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. Switch can be locked in "ON" position for ease of operator comfort during extended use. apply caution when locking tool in "ON" position and maintain firm grasp on tool. To start the tool, push the switch lever "ON (I)" on the left side of the tool. Volts amperes hertz alternating current Class II Construction revolutions or reciprocation per minute number of blow The blows per minute can be adjusted just by turning the adjusting dial. Refer to the table below for the relationship between the number settings on the adjusting dial and the blows per minute. For model HM1317CB only NOTE: · Blows at no load per minute becomes smaller than those on load in order to reduce vibration under no load, but this does not show trouble. Once operation starts with a bit against concrete, blows per minute increase and get to the numbers as shown in the table. When temperature is low and there is less fluidity in grease, the tool may not have this function even with the motor rotating. CAUTION: The adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work. The side handle can be swung 360° on the vertical and secured at any desired position. If the indicator lamp does not light up, the mains cord or the controller may be malfunction. The indicator lamp is lit but the tool does not start even if the tool is switched on, the carbon brushes may be worn out, or the controller, the motor or the ON/OFF switch may be malfunction. [. . . ] ⷠDo not reuse the six bolts but use new ones in the reassembling since these bolts are applied with adhesive. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. For model HM1317CB only CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA HM1317CB




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA HM1317CB will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.