User manual MAKITA LS1013FL

[. . . ] To avoid injury from flying debris, keep holding the saw head down, after making cuts, until the blade has come to a complete stop. When performing slide cut, first pull carriage fully and press down handle, then push carriage toward the guide fence. Always set SUB-FENCE to left position when performing left bevel cuts. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Stopper pin Bolt Blade guard Knob Kerf board Saw blade Blade teeth Left bevel cut Straight cut Right bevel cut Adjusting bolt Turn base Top surface of turn base Periphery of blade Guide fence Adjusting screw Stopper arm Lock lever Grip Pointer Miter scale Lever Arm Bevel scale Lock-off button Switch trigger Handle Switch for laser Socket wrench Wrench holder Center cover Hex bolt Blade case Arrow Shaft lock Inner flange Spindle Ring Outer flange Hex bolt (left handed) Dust nozzle Dust bag Fastener Support Turn base Sub-fence Sub-fence R Screws Vise arm Vise rod Screw Vise knob Guide fence Vise plate Vise nut Holder Knob Vise Spacer block Aluminum extrusion Spacer blocks Horizontal vise (optional accessory) 63 Cut grooves with blade 64 Hex bolts 65 Triangular rule 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 Screw Miter scale Pointer Bevel scale Pointers Arm holder Right 45° bevel angle adjusting bolt Left 45° bevel angle adjusting bolt Hex lock nut Kerf block Work piece Cutting line Vertical vise Screwdriver Screw (one piece only) Lens for the laser light Limit mark Brush holder cap Light Light switch Pull out Push Lamp box Screws Fluorescent tube Dust box Cover Button Cylinder part Sawdust Due to our continuing program of research and development, the specifications herein are subject to change without notice. [. . . ] cAUTION: · When performing right bevel cuts, never use the subfence R. 29) The use of the dust bag makes cutting operations clean and dust collection easy. To attach the dust bag, insert the dust nozzle into the dust spout on the blade case and fit the bag's entry port over the dust nozzle. When the dust bag is about half full, remove the dust bag from the tool and pull the fastener out. Empty the dust bag of its contents, tapping it lightly so as to remove particles adhering to the insides which might hamper further collection. NOTE: If you connect a vacuum cleaner to your saw, more efficient and cleaner operations can be performed. The vertical vise can be installed in two positions on either the left or right side of the guide fence or the base. Insert the vise rod into the hole in the guide fence and tighten the screw on the back of the guide fence to secure the vise rod. If the screw to secure the vise arm contacts the guide fence, install the screw on the opposite side of vise arm. Make sure that no part of the tool contacts the vise when lowering the handle fully and pulling or pushing the carriage all the way. The workpiece must be secured firmly against the turn base and guide fence with the vise during all operations. If the handle is pressed down with force or if lateral force is applied, the blade will vibrate and leave a mark (saw mark) in the workpiece and the precision of the cut will be impaired. During a slide cut, gently push the carriage toward the guide fence without stopping. If the carriage movement is stopped during the cut, a mark will be left in the workpiece and the precision of the cut will be impaired. 41) Workpieces up to 91 mm high and 70 mm wide can be cut in the following way. Switch on the tool without the blade making any contact and wait until the blade attains full speed before lowering. Then gently lower the handle to the fully lowered position to cut the workpiece. When the cut is completed, switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COMPLETE STOP before returning the blade to its fully elevated position. cAUTION: · Firmly tighten the knob clockwise so that the carriage will not move during operation. Switch on the tool without the blade making any contact and wait until the blade attains full speed. press down the handle and PUSH THE CARRIAGE TOWARD THE GUIDE FENCE AND THROUGH THE WORKPIECE. When the cut is completed, switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COMPLETE STOP before returning the blade to its fully elevated position. [. . . ] For model LS1013L, LS1013FL only WARNING: · As the tool is plugged when adjusting the position of laser line, take a full caution especially at switch action. A blow or impact causes the incorrect position of laser line, damage to the laser beam emitting part or a short life of the tool. For model LS1013L, LS1013FL only If the lens for the laser light becomes dirty, or sawdust adheres to it in such a way that the laser line is no longer easily visible, unplug the saw and remove and clean the lens for the laser light carefully with a damp, soft cloth. To remove the lens for the laser light, remove the saw blade before removing the lens according to the instructions in the section titled "Installing or removing saw blade". [. . . ]