User manual MAKITA LS1016L

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA LS1016L. We hope that this MAKITA LS1016L user guide will be useful to you.


MAKITA LS1016L : Download the complete user guide (3732 Ko)

You may also download the following manuals related to this product:

   MAKITA LS1016L (2263 ko)
   MAKITA LS1016L (2263 ko)
   MAKITA LS1016L (2263 ko)
   MAKITA LS1016L (2263 ko)
   MAKITA LS1016L (2263 ko)
   MAKITA LS1016L (2263 ko)
   MAKITA LS1016L (2263 ko)
   MAKITA LS1016L (2263 ko)
   MAKITA LS1016L (2263 ko)
   MAKITA LS1016L (2263 ko)
   MAKITA LS1016L (2263 ko)
   MAKITA LS1016L (2263 ko)
   MAKITA LS1016L (2263 ko)
   MAKITA LS1016L ANNEXE 6 (2225 ko)
   MAKITA LS1016L ANNEXE 79 (2225 ko)
   MAKITA LS1016L ANNEXE 81 (2162 ko)
   MAKITA LS1016L ANNEXE 725 (2225 ko)
   MAKITA LS1016L ANNEXE 973 (2225 ko)
   MAKITA LS1016L ANNEXE 719 (2225 ko)
   MAKITA LS1016L ANNEXE 431 (2225 ko)
   MAKITA LS1016L ANNEXE 843 (2263 ko)
   MAKITA LS1016L ANNEXE 132 (2225 ko)
   MAKITA LS1016L ANNEXE 558 (2225 ko)
   MAKITA LS1016L ANNEXE 643 (2263 ko)
   MAKITA LS1016L ANNEXE 838 (2162 ko)
   MAKITA LS1016L ANNEXE 853 (2162 ko)
   MAKITA LS1016L ANNEXE 361 (2162 ko)
   MAKITA LS1016L ANNEXE 878 (2162 ko)
   MAKITA LS1016L ANNEXE 907 (2162 ko)
   MAKITA LS1016L ANNEXE 570 (2162 ko)

Manual abstract: user guide MAKITA LS1016L

Detailed instructions for use are in the User's Guide.

[. . . ] Cutting capacities Crown molding 45 ° type (with Crown molding stopper used) Base board (H) (with Horizontal vise used) No load speed (RPM) Laser Type (LS1016L only) Dimensions (L x W x H) Net weight Wavelength 650 nm, Maximum output 168 mm (6-5/8") 120 mm (4-3/4") 3, 200/min. Due to our continuing programme of research and development, the specifications herein are subject to change without notice. ⷠNote: Specifications may differ from country to country. Learn the tool's applications and limitations, as well as the specific potential hazards peculiar to it. [. . . ] When the bevel operations are complete, don't forget to relocate the fence. nOTE: · For easy tightening/loosening, the position of the lever can be changed according to your need by pulling it up. WARNING: Before operating the tool, make sure that the upper and lower fences are secured firmly. Before bevel-cutting, make sure that no part of the tool contacts the upper and lower fences when lowering the handle fully and pulling or pushing the carriage all the way. Sliding the fences to inside by loosening the clamping screw only before miter-cutting allows support of workpiece close to the saw blade. The vertical vise can be installed in two positions on either the left or right side of the base. If the screw to secure the vise arm contacts the carriage, install the screw on the opposite side of vise arm. Make sure that no part of the tool contacts the vise when lowering the handle fully and pulling or pushing the carriage all the way. position the workpiece at the desired cutting position and secure it firmly by tightening the vise knob. Turning the vise knob to 90° counterclockwise allows the vise knob to be moved up and down, facilitating the quick setting of workpiece. To secure the workpiece after setting, turn it the vise knob clockwise. CAUTION: The workpiece must be secured firmly against the turn base and guide fence with the vise during all operations. The horizontal vise can be installed in two positions on either the left or right side of the base. When performing 15° or greater miter cuts, install the horizontal vise on the side opposite the direction in which the turn base is to be turned. The holders can be installed on either side as a convenient means of holding workpieces horizontally. Slip the holder rods into the holes in the base and adjust their length according to the workpiece to be held. CAUTION: Always support long workpieces level with the top surface of the turn base for accurate cuts and to prevent dangerous loss of control of the tool. To grip the workpiece, push the vise knob forward until the vise plate contacts the workpiece and flip the vise nut to the right. This could cause the workpiece to be thrown, cause damage to the blade or cause the loss of control, which can result in PERSONAL INJURY. When cutting out thin workpiece, such as base boards, against the fence, always use the horizontal vise. CAUTION: Before use, be sure to release the handle from the lowered position by pulling the stopper pin. Too much force may result in overload of the motor and/or decreased cutting efficiency. [. . . ] After replacing brushes, plug in the tool and break in brushes by running tool with no load for about 10 minutes. Then check the tool while running and electric brake operation when releasing the switch trigger. If electric brake is not working well, ask your local Makita service center for repair. To remove the lens for the laser light, remove the saw blade before removing the lens according to the instructions in the section titled "Installing or removing saw blade". [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA LS1016L




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA LS1016L will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.