User manual MAKITA SP252-4R

[. . . ] 4R INSTRUCTION MANUAL MANUEL D’INSTRUCTIONS BETRIEBSANLEITUNG ISTRUZIONI D’USO GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES MANUAL DE INSTRUÇÕES Important: Read this instruction manual carefully before putting the into operation and strictly observe the safety regulations!We are pleased to offer you a product that is the result of an extensive development program and many years of knowledge and experience. To safely obtain the best possible results from your DOLMAR POWER SPRAYER, please read this manual thoroughly before using the machine, and follow all instructions given herein to ensure proper operation. Table of Contents Page Symbols ጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟ 2 Safety instructions ጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟ 3 Technical dataጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟ 7 Designetion of parts ጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟ 8 Assembly instructions ጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟ 9 Before start of operation ጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟ 10 Mixing aguricultual chemicalsጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟ 12 Starting the engine ጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟ 12 Stopping the engine ጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟ 14 Operation ጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟ 15 Inspection and maintenanceጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟ 16 Troubleshooting ጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟጟ 19 SYMBOLS It is very important to understand the following symbols when reading this instruction manual. [. . . ] € As an example to keep the oil gauge clean, it is recommended to insert the oil gauge on its knob side into the engine cover, as shown in Fig. Upper limit (Edge of oil refill port) If oil adheres around this tip, refill new oil. Point 2 in Replacement of Oil: “If oil spills out” – If oil spills out between the fuel tank and engine main unit, the oil is sucked into through the cooling air intake port, which will contaminate the engine. REFUELING Handling of Fuel It is necessary to handle fuel with utmost care. Refueling must be performed in a sufficiently ventilated room or in the open air. Storage Period of Fuel Fuel should be used up within a period of 4 weeks, even if it is kept in a special container in a well-ventilated shade. If a special container is not used or if the container is not covered, fuel may deteriorate in one day. STORAGE OF MACHINE AND REFILL TANK – Keep the machine and tank at a cool place free from direct sunshine. Be sure to use an automobile gasoline (regular gasoline or premium gasoline). Points for Fuel – Never use a gasoline mixture which contains engine oil. Refueling WARNING: INFLAMMABLES STRICTLY PROHIBITED Gasoline used: Automobile gasoline (unleaded gasoline) – Loosen the tank cap a little so that there will be no difference in atmospheric pressure. € Detach the tank cap, and refuel, discharging air by tilting the fuel tank so that the refuel port will be oriented upward. ) – Wipe well the periphery of the tank cap to prevent foreign matter from entering into the fuel tank. € The tank cap is consumable, and therefore should be renewed every two to three years. When working with aguricultual chemicals, strictly follow the instructions provided by the manufacturer at all times. Always use the provided strainer when pouring aguricultual chemicals into the chemical tank. If chemicals are to be mixed inside the chemical tank, alwys add water before other sguricultual chemicals. cAUTION: • Always handle agricultural chemicals with the utmost care. Should your skin come into contact with agricultural chemicals by accident, immediately rinse the affected area with large amounts of water. cAUTION: • Always handle agricultural chemicals with the utmost care. Take extra care to thoroughly rinse the sprayer tank, pump and nozzle before adding different chemical agents to the sprayer tank. Mixing the residues of previously used agricultural chemicals with other chemical agents may cause toxin-induced diseases. [. . . ] Replace the element in the position indicated by the dotted line in fig. € Use a piece of paper to wipe off any oil adhering to the air cleaner cover and plate breather. € Immediately after cleaning, attach the cleaner cover and use the attachment bolt for fixing. (When remounting, position the upper part of the cover first and then the lower. [. . . ]