User manual MAKITA TM102.16H2

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA TM102.16H2. We hope that this MAKITA TM102.16H2 user guide will be useful to you.


MAKITA TM102.16H2 : Download the complete user guide (2976 Ko)

Manual abstract: user guide MAKITA TM102.16H2

Detailed instructions for use are in the User's Guide.

[. . . ] Avoid injury from getting caught in belt: Do not operate the machine without shields in place. 910 950 1050 (1260) 1800 1150 2420 970 1115 INTRODUCTION EN 1 INTRODUCTION Dear Customer, thank you for having chosen one of our products. We hope that you will get complete satisfaction from using your new lawn-tractor and that it will fully meet all your expectations. This manual has been compiled in order that you may get to know your machine and to be able to use it safely and efficiently. [. . . ] Slowly release the pedal which will turn from «brake» to «clutch», thus operating the rear wheels (☛ 4. The pedal has to be released gradually as a sudden engagement may cause tipping up and loss of control of the vehicle. Gradually reach the desired operating speed using the accelerator and gear lever. To change the gear speed the clutch must be used pushing the pedal down half way (☛ 4. ž For hydrostatic drive models: When moving the machine from one area to another, put the accelerator lever in a midway position between «SLOW» and «FAST». 32) in direction «F» and go to the required speed by progressively increasing pressure on the pedal and moving the accelerator appropriately. 32) to prevent sudden engagement from causing tipping up and loss of control of the vehicle, particularly on slopes. 3 BRAKING First, reduce the machine’s speed by reducing the engine’s r. ž For hydrostatic drive models: NOTE The machine already slows down considerably by just releasing the drive pedal. ž For mechanical drive models: Push down the pedal until the machine stops and then insert reverse by moving the lever sideways and putting it into position «R». Gradually release the pedal to engage the clutch and then begin moving in reverse. ž For hydrostatic drive models: When the machine is stopped, start the reverse movement by pressing the drive pedal in the «R» direction (☛ 4. 5 GRASS CUTTING When you have reached the area to be mowed, Ø 100 make sure that the grass-catcher or stone-guard is Ø 80 correctly fitted and that the cutting deck wheels are positioned at the required height. 1 Each wheel can be fitted at two different heights: the low position always leaves a space between the ground and the edge of the cutting deck to prevent 2 the deck from damaging the lawn if the ground is uneven. To change the position, unscrew and remove the pin (1) then reposition the wheel (2) in the upper and lower hole of the wale corresponding to the wheel diameter. This work is to be done to all four wheels, WITH THE ENGINE OFF AND THE BLADES DISENGAGED. To start cutting: – – – – put the accelerator into the «FAST» position; bring the cutting deck to the highest position; engage the blades (☛ 4. 9); start moving forwards onto the grass area very gradually and with particular caution, as already described; – adjust the forward speed and the cutting height (☛ 4. 10) according to the lawn condition (height, density and dampness of the grass). When cutting on sloping ground, the forward speed must be reduced to ensure safe conditions ( ☛ 1. In any case, the speed should always be lowered if you note a reduction in engine 28 EN HOW TO USE THE MACHINE speed, since a forward speed that is too fast compared to the amount of grass being cut will never mow the grass well. Disengage the blades and put the cutting deck in the highest position whenever you need to get past an obstacle. [. . . ] 102) Improves grass collecting when the cutting deck is close to the ground. From 216 to 240 kg ➤ For mechanical drive models: Forward speed (approximate) at 3000 min. 8 km/h Inside turning circle (minimum diameter of uncut grass - left side): tyres 13 x 5. 5 GB Service, spare parts and guarantee Guarantee DOLMAR guarantees the highest quality and will therefore reimburse all costs for repair by replacement of damaged parts resulting from material or production faults occurring within the guarantee period after purchase. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA TM102.16H2




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA TM102.16H2 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.