User manual MAXDATA MPL 500 1200 3200 CASE

[. . . ] MAXDATA PLATINUM Server Case Users' Manual MAXDATA PLATINUM Server Case Manual 1 2 Part 1 Server Case MAXDATA PLATINUM Server Case Manual 3 4 Contents 1 Chassis Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Additions for the SC5100 Pedestal Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Additions for the SC5100 Rack Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect the I2C cable from the hot swap bay to the HSBP-A connector on the server board. MAXDATA PLATINUM Server Case Manual 21 10. If desired connect the serial port 2 cable to the server board and mount it on the rear or front of the chassis. Connect the USB cable from the front panel to the server board. Install the Diskette Drive NOTE We highly recommend you use a magnetic screwdriver for this step. A nonmagnetic screwdriver may lose the screws between the chassis and the plastic bezel. Using a magnetic screwdriver, remove the two screws that hold the diskette drive carrier to the front of the chassis. Slide the carrier towards the rear of the chassis, until it comes free. Figure 10. Set any jumpers or switches according to the drive manufacturer's instructions. Slide the drive into the drive carrier component side down. 22 Setting Up the Chassis A C B Figure 11. Carrier 7 . Insert and tighten four screws (fine thread flat head) to attach the drive to the carrier. 8. Position the carrier so the front of the drive fits correctly in the front opening of the chassis. When properly positioned, the hole in the carrier aligns with the threaded hole in the frame. Secure the assembly to the front of the chassis with the two screws removed in step 1; tighten the screws firmly. Connect data and power cables to the drive. MAXDATA PLATINUM Server Case Manual 23 A B C Figure 12. Power cable 24 Setting Up the Chassis Hard Drives Drive Cabling Considerations The cables that ship with the chassis are pre-folded to fit the chassis. To minimize the chance of damaging a cable, you should keep the cables folded correctly. The number of devices you can install depends on: · · · The number supported by the bus on your server board The number of physical drive bays available The combination of SCSI and IDE devices IDE Requirements If no drives are present on an IDE channel, the cable must be removed. If only one drive is installed, it should be connected at the end of the cable. NOTE To disable the IDE controller: If you plan to disable the IDE controller to reuse the interrupt for that controller, you must physically unplug the IDE cable from the board connector if a cable is present. Simply disabling the drive by configuring the SSU option does not make the interrupt available. SCSI Requirements If the optional hot swap bay is installed, one Ultra160 SCSI cable is provided with the chassis to connect the hot swap backplane with the server board. This cable should be connected to an LVD connector on the server board. Installing a 5. 25-inch Removable Media Device Two 5. 25-inch half-height bays provide space for tape backup, CD-ROM, or other removable media drives. NOTE Save the EMI shields: EMI integrity and cooling are both protected by having drives installed in the bays or EMI shields covering the bays. When you install a drive, save the shield to reinstall in case you should later remove the drive and not reinstall one in the same bay. CAUTION For proper cooling, you must leave the bottom bay empty. Save the shield for use if you remove the peripheral. MAXDATA PLATINUM Server Case Manual 25 Figure 13. [. . . ] Refer servicing of the power supply to qualified technical personnel. 58 Regulatory Information A Warnings WARNING: English (US) MAXDATA PLATINUM Server Case Manual 59 WARNING: English (US) The power supply in this product contains no user-serviceable parts. Refer servicing only to qualified personnel. Do not attempt to modify or use the supplied AC power cord if it is not the exact type required. A product with more than one power supply will have a separate AC power cord for each supply. The power button on the system does not turn off system AC power. To remove AC power from the system, you must unplug each AC power cord from the wall outlet or power supply. The power cord(s) is considered the disconnect device to the mains (AC) power. [. . . ]