User manual MAXDATA P1500 CASE

[. . . ] MAXDATA PLATINUM 1500R Server Case User's Manual MAXDATA PLATINUM Server Case User's Manual 1 2 MAXDATA PLATINUM Server Case User's Manual Part 1 Server Case MAXDATA PLATINUM Server Case User's Manual 3 4 MAXDATA PLATINUM Server Case User's Manual Content 1 Chassis Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 What Your Kit Includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Items You Must Purchase Separately . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Feature Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Insert the riser card connector into the server board slot while aligning the tabs on the rear retention bracket with the holes in the chassis. CAUTION Press the riser card straight down into the slot. Tipping it in the slot while installing it may damage the riser card or slot. Firmly press the riser card straight down until it is fully seated in the server board slot. Figure 22. Installing a Riser Card on the Server Board 38 Assembling the System Installing a Hard Drive A SCSI system can support two hot swappable hard drives in the drive bays, plus one in the flex bay. An ATA system can support two non-hot swappable hard drives in the drive bays. CAUTION Not all ATA hard drives are supported by this server. Unsupported drives will mechanically not mate with the connector in the drive bay. To see a list of validated manufacturers and hard drive types, go to: http://support. intel. com/support/motherboards/server CAUTION To allow proper airflow and server cooling, all drive bays must contain either a carrier with a hard drive installed or a carrier with an air baffle installed. Remove the air baffle (Figure 23, A) from the drive carrier by removing the four screws (B) from the slide track (C). Store the air baffle for future reinstallation in the event you must operate your server without a drive in one of the bays. Figure 23. Removing an Air Baffle from a Drive Carrier MAXDATA PLATINUM Server Case User's Manual 39 4. Remove the hard drive from its wrapper and place it on an anti-static surface. Set any jumpers and/or switches on the drive according to the drive manufacturer's instructions. With the drive circuit-side-down (Figure 24, A), position the connector end (E) so that it is facing the back of the carrier (B). Align the holes in the drive to the holes in the drive carrier slide track (C), insert the screws (D) that you previously removed, and attach the carrier to the drive. Figure 24. Slide the carrier/drive all the way into the drive bay with the retention lever in the fully open position. Push the retention lever closed to secure the carrier/drive in the bay. Reinstall a carrier/air baffle in any bays where you are not installing a carrier/drive. 40 Assembling the System Installing a CD-ROM Drive/FDD Module Your server does not come with a CD-ROM drive or floppy disk drive. As an accessory, Intel® offers a slim-line CD-ROM drive/FDD module that you may purchase and install in the flex bay. Slide the module into the flex bay until you feel the connectors touch. Push the module in about 3/16 of an inch (5 mm) more to fully engage the connectors. If you have finished your work in the peripheral bays, install the bezel. Figure 25. Installing a CD-ROM Drive/FDD Module MAXDATA PLATINUM Server Case User's Manual 41 Installing a Bezel Place the bezel between the chassis handles and push it toward the front of the chassis until it snaps into place. Figure 26. [. . . ] Mettez hors tension tous les périphériques connectés au système. Mettez le système hors tension en mettant l'interrupteur général en position OFF (bouton-poussoir). Identifiez et débranchez tous les câbles reliés aux connecteurs d'E-S ou aux accès derrière le système. Pour prévenir les décharges électrostatiques lorsque vous touchez aux composants, portez une bande antistatique pour poignet et reliez-la à la masse du système (toute surface métallique non peinte du boîtier). [. . . ]