User manual MAXDATA P5200 CASE

[. . . ] MAXDATA PLATINUM 5200 Server Chassis User's Manual MAXDATA PLATINUM 5200 Server Chassis 1 2 Contents 1 Chassis Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Feature Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Chassis Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] An optional second Hot-Swap Drive Bay is available. 12 Chassis Description Power Supply The 650 watt, dual-line cord, 2+1 redundant power supply is auto ranging for either 100-120 VAC or 200-240 VAC. The MAXDATA PLATINUM 5200 Server Chassis Hot-Swap, Redundant Power ships with two power modules and a blank filler installed. A third power module (includes a second power cable) can be ordered as an accessory . NOTE A redundant power configuration requires installation of three power modules and two power cords. Figure 7. Redundancy LED Description LED Name AC1 Color Green Condition ON OFF AC2 Green ON OFF ACR Green ON OFF Description AC Power Cord 1 (AC1) active and modules 1 & 3 active No AC power to AC Power Cord 1 AC Power Cord 2 (AC2) active and modules 2 & 3 active No AC power to AC Power Cord 2 Redundant Power active: all 3 modules active; both power cords active Redundant Power not active MAXDATA PLATINUM 5200 Server Chassis 13 Table 4. Power Module LED Description LED Name Power Module LED Color Green Green Amber Condition ON BLINK ON Description Power supply DC outputs ON and OK AC power present/Only Standby outputs ON Indicates one of these conditions: · No AC power to this power supply module · Power supply failure (includes over voltage, over temperature) · Module current limit exceeded Check Server Management Software to diagnose problem OFF No AC Power to System Checking the Power Cords WARNING Do not attempt to modify or use the supplied AC power cords if they are not the exact type required. The power supply cords are the main disconnect device to mains (AC power). The socket outlet shall be installed near the equipment and shall be readily accessible. If a power cord supplied with the chassis is not compatible with the AC wall outlet in your region, get one that meets the following criteria: · · The cord must be rated for the available AC voltage and have a current rating that is at least 125% of the current rating of the server. The connector that plugs into the wall outlet must be a grounding-type male plug designed for use in your region. It must have certification marks showing certification by an agency acceptable in your region. The connector that plugs into the AC receptacle on the power supply must be an IEC 320, sheet C13, type female connector. In Europe, the cord must be less than 4. 5 meters (14. 76 feet) long, and it must be flexible <HAR> (harmonized) or VDE certified cordage to comply with the chassis' safety certifications. · · Chassis Security To help prevent unauthorized entry or use of the server, the chassis includes two chassis intrusion switches that can be monitored by Server Management software, a padlock loop at the rear of the chassis, and a front bezel door lock (pedestal only). Monitoring Two chassis intrusion switches are preinstalled. When the access cover is removed or the front bezel door is opened, the switch transmits a signal to the BMC on the server board. Server management software can be programmed to respond to an intrusion by powering down or by locking the keyboard, for example. 14 Chassis Description Mechanical Locks A padlock loop on the rear of the chassis access cover can be used to prevent access to the inside of the chassis. A variety of lock sizes can be accommodated by the . 270 inch (7 mm) diameter loop. The front bezel has a two-position lock to prevent access to the hard drives and the interior of the chassis. Figure 8. B. Front bezel locked Front bezel unlocked MAXDATA PLATINUM 5200 Server Chassis 15 16 Chassis Description 2 Setting Up the Chassis Install the Chassis Feet (Pedestal Mode) If you are installing this server into a rack system, skip these steps and read the instructions that came with your rack kit. The holes in the feet will line up with only one set of holes in the chassis. On the front foot, the middle hole should be towards the front of the chassis. Hole locations for the front foot are marked "F" and "1, 2". On the back foot, the middle hole should be towards the back of the chassis. You are now ready to attach a monitor, keyboard, and mouse to your server, and turn it on. D Figure 9. [. . . ] Turn off the system by pressing the power button on the front of the product. Disconnect the AC power by unplugging all AC power cords from the system or wall outlet. Disconnect all cables and telecommunication lines that are connected to the system. Upon completion of accessing inside the product, refasten access cover with original screws or fasteners. [. . . ]