User manual MEDION 42 PLASMA DISPLAY MD 41842

[. . . ] Installation And Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 7. 4 7. 5 7. 6 7. 7 7. 8 7. 9 7. 10 7. 11 7. 12 7. 13 7. 14 7. 15 Description Pages 44 44 44 44 44 44 44 44 45 45 45 45 Colour Display . . Important: The supplier constantly strives to improve the quality of product documentation. We ask that you inform us about vague descriptions, drawings or ambiguous terms. [. . . ] It provides a cinch plug-and-socket connector which is a very reasonable and simple link, and is frequently utilised as a link to video recorders. · The SCART 1 video input provides the connection to CVBS, Y/C (S-Video) and RGB video inputs, a CVBS output for connecting a video recorder, and audio inputs & outputs. · The SCART 2 video input provides CVBS, Y/C (SVideo) video inputs, a CVBS output for connecting a video recorder, and audio inputs & outputs. · The RF tuner input with IEC jack links the display for connection of terrestrial antennas or cable channel systems. · The combined input DVI-I (analogue and digital) serves for the connection of high-resolution graphic card signals. · The RS232 control input for connecting a PC facilitates diagnosis in the event of servicing. · The OSD input menu enables you to select the desired video input. · The "ADJUSTMENT" menu enables you to set the configuration of inputs so that, for example, the same input is presented after turning on the display. 19 3. 2 Connection to Compatible PC's are not sure about which jack the monitor is to be connected to, you can read more about this in either the graphics card or computer user manuals. Please use only the enclosed signal cable for connection. The plasma display is suitable for utilisation together with compatible computers. Your PC has one of the following configurations: · A built-in graphics adapter. Both variations have one analogue and one digital video output jack for connection of a monitor. If you 20 For the connection of your monitor to the system, proceed as follows: 1. In case it is necessary, install a graphics card according to the directions in the graphics card user manual. Operating mode at the beginning of utilisation The operating mode of the technology applied recommends the viewing of predominately motion images or at least the constant alternation of still frame images for the first 100 hours. Image sticking The manufacturer would like to point out to you that during lengthy viewing of freeze pictures (e. g. PC playback), the image is still slightly visible in the full mask for a few minutes during the subsequent playback of a different source. This "vanishing" residual image is caused by the system, and does not represent a flaw. Video cable A high-quality 75 coaxial cable should be utilised for the connection of the video signal. Poor quality signal cable can result in strong disturbances and formation of shadows in the displayed image, as well as exceeding the permissible EMC level. The mechanical interlocks of the individual plug-and-socket connectors are necessary for perfect and safe operation of the device. 21 ! CAUTION 4 Remote control 4. 1 Direct Functions 22 · The remote control only functions if the plasma display has been turned on with the mains switch beforehand. STDBY After you have turned on the display once with the mains switch, you can turn it on and off with the remote control (stand-by). Press the stand-by button in order to switch the display into stand-by mode. CAUTION: If the display has been turned on in standby mode, it is still linked with the mains. For complete disconnection you must first switch the mains switch into the "off" (0) position, and then pull the mains cable. TV VIDEO You can switch directly to TV mode with this key. You can switch directly to VIDEO mode (SCART1 -> SCART2 -> CVBS -> Y/C) with this key. [. . . ] Please contact our service department for more extensive information. 7. Technical Specifications 7. 1 Product Attributes The colour plasma display complies with the following specifications, when · the power supply lies within the specified range, · the display has been in operation for at least 30 minutes, · the timing, video input and the display size are specified as follows. Where no other information is effected, all details in these technical specifications have been measured in accordance with the VESA Standard Display Specifications and Test Procedures. · OSD and IR remote control Clearly coherent and well-designed menus and the operation of the IR remote control make the operation of the diverse input sources as easy as child's play. [. . . ]