User manual MEDION GOPAL NAVIGATOR 2.0 AE

[. . . ] User Manual Navigation Software -2- Table of Contents 1 Starting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 1 Important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 2 Alternative installation of navigation software from a memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 3 Further map material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please hereby ensure that there is sufficient storage space on your memory card. If you have copied digitalised maps of several countries or country groups to your memory card, you must select the required country map in the navigation application of your device. 1. 5 Transferring installation files and map material to the internal memory Your device features an internal, non-volatile memory Contained in the \My Flash Disk folder. Via ® ActiveSync you can use the Search option to display this and further folders. Manipulations to folders and files can be performed as in an explorer. The necessary folders must be created to make installation files and map material available to the device. Create the INSTALL folder (\My Flash Disk\INSTALL) for the installation files. Store map material in the MapRegions (\My Flash Disk\MapRegions) folder. Should additional data be stored on your navigation device, please note that sufficient capacity must be available on transferring data. Note The navigation system must be linked to the computer via ActiveSync (see device manual) for data transfer. ® 1. 6 Data transfer (GoPal Assistant) The GoPal assistant is available for transferring installation files and card data to the navigation device. In this case, use a memory card reading device or ActiveSync connection. -7- 1. 6. 1 Transferring the installation files Note Please note that the memory card is formatted before the data transfer!Please therefore ensure beforehand that there are no important files still on your memory card!Before installing the software you must transfer the installation files using the GoPal Assistant as follows: a. The software will start up automatically when you insert the DVD into your PC drive. If the software does not start automatically, you can also run it directly from the DVD in Windows Explorer by clicking on the GoPalAssistant. exe file (directory: Assistant). Insert your memory card in the card reader or connect the navigation device via ActiveSync to your PC. Select the drive for your memory card or drive linking ActiveSync to your computer. You can now transfer the navigation software installation files from the DVD to your memory card by clicking on Transfer software. Note Please note that software installation in the navigation system is only performed following a hard reset (see: device manual). ® ® 1. 6. 2 Transferring the map data Once the installation files have been transferred to your memory card you can create your own personal map area using a general map. Later on you can adapt your personal map area using the GoPal Assistant, i. e. The software will start up automatically when you insert the DVD into your PC drive. After zooming in or out, you can use this switch to reactivate Autozoom. You can select a destination directly from the map. If your desired destination is not in the area touched, you can use the menu bar at the bottom of the screen to switch to further areas nearby. [. . . ] This can be used to adjust the brightness of the screen. - 18 - In order to save electricity, you can use this input template to select periods for mains and battery operation, after which the unit will switch off. In this view you can see the charging status of the battery of your unit and also whether charging is in progress. 2. 6. 2 Display You have the following options for the display: The map is displayed in north orientation or in the direction of travel, depending on the scale of the map (2D-map view). The map always turns according to the direction of travel (2D-map view). The zoom function remains active in the 3D map, but it is no longer possible to move the map. [. . . ]