User manual MEDION GOPAL 4.5 QUICK GUIDE

[. . . ] Software manual GoPal Navigator Version 4 GoPal Navigator Version 4 Contents CHAPTER 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Greeting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Contents of CD/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To calibrate the device, follow the instructions on the screen by tapping the target sign. Finally, accept the new settings by tapping the screen again. Note If you format the flash memory of your navigation device in order to, for example, update to a newer version of the software, the screen must also be recalibrated during installation (refer also to the device manual). The brightness settings will be saved and the stored value will be used the next time your start-up your navigation system. Power management This sub-menu enables you to adapt the energy options for either battery or mains operation as well as to check the current charge status. · If you tap the selection menu under the entry Battery mode: Turn off device after: you can select one of the following options from the list in the relevant pop-up menu: o Never turn off device The navigation device is only switched off when the capacity of the internal battery has been exhausted. o 15/30/45 min/ 1/2 hr If the navigation device is neither in use nor currently navigating, it is switched to stand-by mode following a pre-set period of time: When you press the ON/OFF switch, the device is reactivated and the most recently active screen is displayed. · If you tap the selection menu under the entry Main supply: Turn off device after: you can select one of the following options from the list in the relevant pop-up menu: o Never turn off device The navigation device is never switched off. o 15/30/45 min/ 1/2 hr If the navigation device is neither in use nor currently navigating, it is switched to stand-by mode following a pre-set period of time: When you press the ON/OFF switch, the device is 24 Adjusting the settings reactivated and the most recently active screen is displayed. · The current charge of the battery is displayed on a bar chart on the lower portion of the screen. The following statuses are defined: o Battery is loading The navigation device is connected to an external power source via USB: The bar chart shows that the internal battery is currently being charged. o Energy remaining The navigation device is not connected to an external power source and is being operated by battery: The remaining battery capacity is shown as a percentage. o External power supply The navigation device is connected to an external power source via USB: The internal battery is being charged. Auto OFF function In this sub-menu you determine how the device reacts when the power supply plug is pulled out while charging or while the device is in operation. · Deactivate Auto OFF If you tap the option Deactivate Auto OFF in the list, Auto Off mode is not executed: The device remains switched on regardless of the status of the power supply until the internal voltage has been exhausted. In this case, the settings you set in Power Management (see previous page) are valid. · 1 Minute When you tap the option 1 Minute in the list, the device is automatically switched off 1 minute after the plug has been pulled out. 2 Minutes When you tap the option 2 Minutes in the list, the device is automatically switched off 2 minutes after the plug has been pulled out. 5 Minutes When you tap the option 5 Minutes in the list, the device is automatically switched off 5 minutes after the plug has been pulled out. · · If you did not select Deactivate Auto OFF, your navigation device displays the following screen after the power supply plug has been pulled out. 25 Adjusting the settings · · · The The The button returns you to the screen that was active before the plug was pulled out. button restarts the device. Note Please be aware that this function is only available on certain types of device. FM transmitter Further information about the FM transmitter settings can be found in the device manual. Note Please be aware that this setting is only available on certain types of device. Restore factory settings This button allows you to restore the factory default settings to the device. All personal settings such as favourites or the last entered destinations are deleted in the process: Accordingly, you should only perform this function when you no longer need this information. When you tap the button, a confirmation message pops up on your navigation device. Tap the button to restore the factory settings: Otherwise you can cancel the process with the button. When you tap the button, the device is restarted and the following settings are reset: After the restart you must then select the language within the software. In addition, you have another opportunity to familiarise yourself with your navigation system by way of a brief introduction after the navigation software starts: You can also skip this step and start operating your navigation system immediately, as required. Specific settings for the navigation software Following start-up your navigation system functions with standard settings which can, however, be changed and adapted to your personal needs in the Settings menu at any time. [. . . ] In addition to the visual navigation, all manoeuvres are also announced using voice commands. You can adjust the voice output during navigation as follows: · button in the upper left area of the screen: The setting menu Volume then opens, Tap the which allows you to individually set the volume for voice output, the key click and audio playback of MP3 files using the additional MP3 Player application. The volume set here applies equally to playback via the internal speakers and via the earphone connection (3. 5 mm mini jack) on your navigation device. o The buttons and allow you to individually lower or raise the volume for the respective signal output in six steps. [. . . ]