User manual MEDION GOPAL 5.0 ROGRAMVARAN

[. . . ] Software manual GoPal Navigator Version 5 GoPal Navigator Version 5 Contents CHAPTER 1: INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Greeting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Contents of CD/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 System requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If you do not operate your navigation system in one of the following languages, you can skip the next sections. The following languages are currently supported: · German · English · French · Italian · Dutch · Spanish While manual operation of your navigation system is possible at all times, the voice command function must be activated separately: this ensures that your navigation device only reacts to certain voice commands and does not accidentally misinterpret other parts of the conversation. Proceed as follows to start the voice command function for your navigation system: · Touch any point on the screen for around two seconds. A tone then sounds (a rising tone sequence): The voice command function is now activated on your navigation device. · Alternatively, if your navigation device has a so-called Push-to-Talk-button (PTT), you can press this for around 2 seconds. A tone then sounds (a rising tone sequence): The voice command function is now activated on your navigation device. Note If your navigation system prompts you for input via a voice message, no additional tone is emitted. During normal operation, the voice command function is ended once route planning has been entered successfully or the navigation system has not received a voice command for a certain period of time. If necessary, however, you can also stop the voice command function before this. Proceed as follows to stop the voice command function for your navigation system: · Touch any point on the screen for around two seconds. A tone then sounds (a descending tone sequence): The voice command function on your navigation device is now deactivated. · Alternatively, if your navigation device has a so-called Push-to-Talk-button (PTT), you can press this for around 2 seconds. A tone then sounds (a descending tone sequence): The voice command function on your navigation device is now deactivated. 27 Operation using the voice command function Note The allocation of the PTT function button differs from device to device. Information regarding which button carries out the PTT function on your device can be found in the device manual. The voice command or voice recognition function is based in principle on the language set when your navigation device is installed. If, for example, you have selected "German" as the language for your navigation system, the voice command function will also be in German. The following points must be observed when using the voice command function: · Try to speak naturally!· Strong dialects, speaking too clearly or too loudly may interfere with the voice command function. · When using the voice command function, avoid loud background noise such as the radio or ventilation. · For safety reasons, entries may not be made by the driver whilst driving: Please make the necessary entries before beginning the journey. Tip There are special terms for destinations entered for journeys abroad: While entries for functional control (such as the destination entry itself) are made in the pre-set language (e. German), the destination and street names must be entered in the language of the destination country: for planning a route to a destination in France, the destination information must be entered in French. This can, however, lead to voice recognition being affected by foreign accents. The voice command function in practice In the menus there are selected functions which can be controlled using the voice command function. The following section describes which functions can be controlled using the voice command function and which commands must be given to do so. [. . . ] The GoPal Assistant saves the IDs of all navigation devices connected to the PC and lists them in Devices. The navigation device currently connected is identified by a green button. If you select the connected navigation device in Devices, the following information about the device appears in the data selection area: · Name The current name of the device is displayed here. You can rename the device at any time (see below). ® 61 Installation and start-up using the GoPal® Assistant · Device ID The identification number of the device hardware is displayed here. [. . . ]