User manual MEDION MD 20081 CODE LIST

[. . . ] We have structured these instructions so that you will be able to read the information needed subject-related at any time. Keep the instructions safe, in order for you to be able to pass them on to a new owner, in the case of you selling the monitor. These instructions are intended for both first times users and those with previous experience. We have selected the components that make up this product with an attention to functionality, ease of operation, safety and reliability. [. . . ] Ensure that the TFT monitor has not yet been connected to the electricity supply (mains plug not yet plugged in) and that neither the TFT monitor nor the computer has been switched on. Prepare your computer for the TFT monitor if necessary, so that the correct settings for it will be present. Now connect one end of the mains cable supplied with the device to TFT power supply connection and then the other end to an appropriate socket. The mains socket must be in the vicinity of the TFT monitor and be easily accessible (use the same electricity circuit as for the PC). Switch your monitor on at the Standby/On switch on the front of the device. Bringing the device into operation Please pay attention to the following: The monitor device should be set up so that mirror effects, fading and strong contrasts between light and dark are avoided (even if the view from the window is still so attractive!Surface supporting the hands: 5 - 10 cm Highest monitor line at eye level or somewhat below it Viewing distance: 40 to 70 cm Leg-room (vertical): At least 65 cm Leg-room (horizontal): At least 60 cm Press this button again if you wish to leave the OSD. + + Power block, when the OSD is not activated OSD block, when the OSD is not activated Hold the key combination until the bar displayed has moved from left to right completely, to activate/de-activate the block. Select a parameter and reduce its value with this button, when the OSD is switched on. If you are not in the OSD: direct call-up of the Contrast/Brightness menu. Select a parameter and increase its value with this button, when the OSD is switched on. No parts to be maintained or cleaned are located within the monitor casing. Always pull out the mains plug and all connecting cables before cleaning. Do not subject the screen to either dazzling sunlight or to ultra-violet radiation. Please keep the packaging material and use this exclusively to transport the TFT monitor. Packaging is made from materials that can be disposed off in an environmentally friendly way and taken to correct recycling. Device Do not throw the device into the normal domestic refuse after the end of its useful life under any circumstances. Obtain information about the possibilities of environmentally friendly and correct disposal. Model Monitor size Size ratio Nominal voltage Nominal electricity Resolution Brightness Contrast Reaction time Viewing angle h/v RGB input, analog RGB input, digital Audio Input Audio Output User control Temperatures Not in operation -20° C ~ +60°C Moisture (Non-condensing) Weight (gross/net) Dimensions (WxHxD) Power consumption (Stand-by) Power consumption (operation) In operation < 80% Not in operation < 90% 6. 9 m control transistors are used in the case of Active Matrix TFTs with a resolution of 1680 x 1050 Pixeln (WSXGA), each composed of three sub-pixels (red, green, blue). A failure or incorrect control of pixels or individual sub-pixels can arise occasionally, because of this very high number of transistors and the extremely complex manufacturing process associated with it. There have been continuous approaches to define the number of permitted pixel errors in the past. [. . . ] To the extent permitted by law, this warranty shall be void in the event that defects or loss caused by: a. Failure and damage resulting from the operation of the product in an environment other than that recommended in the accompanying user or instruction manual (e. In direct sunlight or in a damp room); accidental damage; use other than in accordance with the accompanying user or instruction manual; modifications, conversions, expansions, maintenance and/or repairs made to the MEDION product by unauthorised repairers or use of unauthorised third party parts; negligence; virus attack or software errors; or improper transportation or packaging during return of the product. This warranty will also be considered void if labels or serial numbers of the product or of a component of the product are modified or made illegible. [. . . ]