User manual MEDION UNIVERSAL REMOTE CONTROL CODELIST

[. . . ] The device has a safety system that prevents the emission of dangerous laser rays escaping from the device during normal use. In order to avoid injury to the eyes, never interfere with or damage the unit's security system. Do not subject your remote control to dust, strong sunlight, moisture, high temperatures or strong vibrations. Battery instructions Keep children away from the batteries. Seek medical attention immediately in the event of a battery being swallowed. [. . . ] Press a number key for a required manufacturer according to the following overview: Key 1 = Medion, Tchibo Key 2 = Philips, Radiola, Philco, Erres, Pye Key 3 = Sony, Akai, Panasonic, JVC, Sharp, Toshiba, Daewoo Key 4 = Thomson, Brandt, Fergusson Key 5 = Saba, Nordmende, Telefunken Key 6 = Grundig, Blaupunkt Key 0 = all brands. Perform the function test now by pressing the PROG+, or PLAY keys (VCR only) until the device changes channel, switches off or responds accordingly. 17 Univ-FB_MD 81302_UK. fm Seite 18 Montag, 7. August 2006 11:08 11 The code search begins with the code that is currently stored. While the search is running, the word SEARCHING (along with the selected device type) is displayed. If you miss the code, you can go back step by step with the PROG­ key. When the device responds accordingly each time a key is pressed, press OK to save the code. The remote control returns to normal operation. Code identification If you want to know which code is saved on a particular mode key, simply press this key. The selected device type and device code appear. 18 Univ-FB_MD 81302_UK. fm Seite 19 Montag, 7. August 2006 11:08 11 Normal operation Operating individual devices After you have finished programming your remote control for your audio/video devices, the remote control will work in the common main functions just like the original remote control for the respective device. Point your remote control at the desired device and press the relevant mode key. [For the universal functions ­ see "Universal functions ("Punch Through")" on page 30 ­ you do not need to press the mode key in advance. ] Activate the functions by pressing the corresponding function key on your universal remote control. Some devices can be switched on and off with the POWER/ ALL OFF key Devices switched off in such a way will, if they were switched off, be switched back on when you perform the ALL OFF function. 20 Univ-FB_MD 81302_UK. fm Seite 21 Montag, 7. August 2006 11:08 11 Set timer The universal remote control has two timer functions: a sleep-timer for the TV (automatic switch off after 1 to 90 minutes); "Zzz" appears in the display: four additional times for customisable commands (e. g. switching to another programme); the bell symbol appears in the display. TV sleep-timer Set sleep-timer 1. Use the arrows to enter the time after which the TV device should switch itself off automatically. 7. Press OK" The SUCCESS confirmation message appears along with the TV timer symbol "Zzz". Lay the universal remote control down so that it is pointing towards the device and is not obstructed. Switch off sleep-timer If a sleep-timer is on ("Zzz" appears in the display) TV SLEEP CLEAR appears in the display instead of TV SLEEP SET when you perform the steps described above. Press OK" The SUCCESS confirmation message appears. 21 Univ-FB_MD 81302_UK. fm Seite 22 Montag, 7. August 2006 11:08 11 Command timer The clock must be set for this timer. You can use the command timer to program a function that is to run automatically at a particular time within the next 24 hours. The command series can contain up to four commands, the first command must always be the selection of a mode key. The following keys are not available for the remaining three commands: the mode keys, the joystick (arrows and OK), MACRO, SETUP, EXIT. [. . . ] If no macro is saved under the selected numberkey, the message MACRO 1 VOID appears. 28 Univ-FB_MD 81302_UK. fm Seite 29 Montag, 7. August 2006 11:08 11 Deleting macros Perform steps 1 to 3 as described in section "Programming macros" on page 27. Press the number key where the macro is stored for the macro that you would like to delete. PLEASE WAIT appears again in the display, followed by the confirmation message SUCCESS. The remote control returns to normal operation. 29 Univ-FB_MD 81302_UK. fm Seite 30 Montag, 7. [. . . ]