User manual MEDION UNIVERSAL REMOTE CONTROL MD 81302

[. . . ] Protection against unexpected battery discharging 6 6 6 6 The display . August 2006 11:08 11 Safety instructions Please read these instructions carefully before operating the remote control. Keep the instructions in a safe place for future reference or in case you need to pass them on to someone else. General information Do not attempt to repair the remote control yourself. The universal remote control contains an infrared laser class 1 diode. [. . . ] [For the universal functions ­ see "Universal functions ("Punch Through")" on page 30 ­ you do not need to press the mode key in advance. ] Activate the functions by pressing the corresponding function key on your universal remote control. The symbol for infrared transmission appears each time you press a key. Each time a key is pressed the display backlight switches on for between 10 and 60 seconds (to set this duration please read: "Backlight" on page 11). Please note: - In certain circumstances, not every function of your original remote control may be directly available on the universal remote control. - Especially for newer devices, it might be possible that the functions are stored to different keys than expected or may not even be available at all. In these cases you can use the learn function to transfer the functions of your original remote control to the desired keys of the universal remote control (see "Learn function" on page 24). SHIFT function After you program a device code, the universal remote control keys can have double functions (with the exception of the S_(Setup) and MACRO keys). To use the second function, briefly press the S (SETUP) key and then (within 15-20 seconds) press one of the secondary function or number keys. Try out which additional functions a key has for a particular device code. Recordings The (Record) key for recording (e. g. This acts as a protection from accidental recordings. EPG ­ Electronic Programme Guide The EPG ("Electronic Programme Guide") key has various functions depending on which code has been used: For TV and satellite codes (e. g. For DVD codes the button opens the title menu. 19 Univ-FB_MD 81302_UK. fm Seite 20 Montag, 7. August 2006 11:08 11 For VCR codes you can use the button for programming, if your video recorder has a Showview function. If the device has both an EPG and a Showview function, the EPG function is given priority. Operating combined devices Combined devices are for example a TV set with an integrated video recorder, a TV set with a DVD player or a DVD recorder with a video recorder. Several controlling options are available to combined devices. Combined devices with two device codes Some combined devices (e. g. TV set with video recorder) require two device codes - one for each device part. Program the correct TV code on the TV mode key and the video recorder code on the other mode key. The combined device is then controlled like two separate devices. Combined devices with one device code Other combined devices only require one code. In this case, you must first select the device part you would like to operate. Now activate the DVD part in the combined device by holding down the DVD mode key for longer than one second. To activate the video recorder in the combined device, first briefly press the S (Setup) key for the SHIFT function, then the DVD mode key. If your combined unit only requires one code but you would like to operate it with two mode keys, then proceed as follows: Programme the device code to two mode keys. Use the learn function (see "Learn function" on page 24 ) to transfer the desired functions of the other unit part to the other mode key. ALL OFF function You can switch off all pre-programmed devices at the same time. Press the POWER/ALL OFF key twice in rapid succession and keep it pressed down after the second time for approx. [. . . ] August 2006 11:08 11 Universal functions ("Punch Through") The universal functions (also called "Punch Through" functions) enable you to carry out certain functions on a different device type than the programmed one. These are the volume, mute and playback functions. Playback functions If the remote control is in TV, SAT or cable mode (devices without playback function), the PLAY, STOP, PAUSE, FAST FORWARD/BACK, and in some cases RECORD keys will control a connected video recorder, DVD player or video recorder. This Punch Through control does not work if the programmed TV, SAT or cable code has its own video recorder function (for example in the case of a combined TVvideo recorder device). Volume/mute Image transmitting devices connected to a TV (e. g. When the universal remote control is controlling this type of device and the VOL (Volume) or ( ) (Mute) keys are pressed, the volume control is transferred to the TV. [. . . ]