User manual MINOURA P-500AL-2

[. . . ] Only when you cannot get enough service, you can contact us. MINOURA North America (for U. S. Phone 1-510-538-8599 Fax Mail 1-510-538-5899 support@minourausa. com MINOURA Japan Headquarters (for ALL worldwide customers) 1197-1 Godo, Anpachi, Gifu 503-2305 Japan Fax Mail Web +81-(0)584-27-7505 minoura@minoura. jp www. minoura. jp MADE IN JAPAN -1- How To Setup Your P-500AL-2 Required Tools: 1 x 5mm Hex Wrench (included) 1 x 10mm Spanner 1 x 13mm Spanner Cradle Bar Top Frame Cradle Hook Bolt Variation A) Cradle Support Main Pillar Type-A (plain type) Type-B (w/ spring washer) Type-C (w/ flat & spring washers) Front Leg (L) C) Alloy Bar & Cradle Hook B) Angle Adjust Plate (projection is foreside) Support Bar Rear Leg Completed Bike Cradle (order is C, B and A from foreside) Foot Adjuster Base Plate Front Leg (R) <Fig. A> Front Leg (L) 1 Connect both Front Legs to the Base Plate using the Collar, Flat Washer, M6x35 Bolt (type-A) and Nylon Nut. [. . . ] Insert the Plastic Shim between the Support Bar and the Main Pillar, then tighten them with the Tighten two bolts in Step-4 firmly. M6x70 Bolt (type-A), M6 Flat Washer and Nylon Nut (see Fig. E> Plastic Shim Flat Washer Nylon Nut Support Bar ! Be sure the Support Bars are on the INSIDE of each Front Leg. 6 7 8 Attach the Cradle Hooks from behind of the Alloy Bar then screw the bolts from the front side. The hook distance will be adjusted later to fit the actual bike frame size. F> Place the Alloy Bar onto the Angle Adjust Plate, then screw to the upper hole on the Cradle Support with the M6x20 (type-A) bolt. G> M6x20 Bolt (A) Install each Bike Cradle to the Main Pillar. To install the Stainless Band Clip, follow the steps below; 1) Once disassemble the Stainless Band Clip. 2) Open the band and wind it around the Main Pillar. Arch side M6x14 Bolt (C) <Fig. H> Stainless Band (45mm) Plastic Bracket Flat Washer 3) Lap the band ends (see Fig. It should be 5) Put the bolt into the hole on the hook, then screw into the 6) Adjust the hook position and tighten the bolt firmly. J> ! If the inside band end with welded nut has been angled against the bolt, you won't be able to screw the bolt in. Make sure the nut side end is properly set at right angle to the bolt. The band end will have to be bent and you are no longer tighten the bolt. Bottom Arch 90º <Fig. K> Stainless Band must be located in upper position ! Bottom Arch must be located in lower position <Fig. L> -3- 9 Assemble the upper Bike Cradle for the Top Frame. M) lower bolt is M6x14 (type-C). Put the Alloy Bar onto the Angle Adjust Plate and install them to The upper bolt is M6x20 (type-A) with a spring washer, and the Top Frame Angle Adjust Plate 10 Insert the Top Frame to the Main Pillar. [. . . ] Using the Foot Adjusters, make sure all feet are contacting the (see Fig. Then tighten the Lock Nut using a 13mm spanner. 13 Place your bike on the Bike Cradle using both hooks supporting greater stability. ! If your bike has a heavily sloping top tube, change to hook the juncture of the seat tube and seat stay to set your bike more stable. [. . . ]