User manual MITSUBISHI AH129

[. . . ] Before Use A new battery must be fully charged before initial use. INSTALLING THE BATTERY Insert the top of the battery into the recess on the back of the phone. Attach it to the phone by pressing slightly upward on the battery and in at the bottom until the locking catch snaps into place. Make sure the battery is properly secured. Getting Started REMOVING THE BATTERY Turn the power off before removing the battery. To remove the battery, press the bottom upward and gently lift the battery off the phone. 1 CHARGING THE BATTERY FOR THE FIRST TIME Connect the AC rapid charging plug into the socket at the base of the phone and plug it into a standard 120 volt AC outlet. [. . . ] Once the A-KEY is programmed, it may not be viewed through the display or any device attached to the phone. FUNCTION MENU User action: FCN + FCN Menu w To RCL RCL -MenuPush v/w w/v (FCN FCN) (Standby only) Action FCN 1 Own Tel w/v FCN Tel:123 4567890 26 FCN 2 Alpha w/v FCN Alpha Input FCN 3 Redial w/v FCN Redial ON FCN 4 System w/v FCN System Pref A FCN 5 AutoAns w/v FCN AutoAns OFF FCN 6 Lock v w FCN Lock Code FCN 7 Last w/v FCN Last MMmSSs FCN 8 Oper w/v FCN Oper HHHhMMm FCN 91 Restr. w/v FCN Security Code Security Code Restr. NoRestr Unlock 123 FCN 92 Unlock w/v FCN 27 FCN 93 Status w/v FCN Security Code Security Code Status ON PIN ON FCN 94 PIN w/v FCN FCN 95 PIN No. v FCN Secure Code PIN No. 1234 DIRECT ACCESS FUNCTION w FCN 0 Pause w/v FCN(1s) Mute w/v FCN(1s) View w/v FCN STO AutoSto w/v FCNSEND AutDTMF w/v FCN v/w RingVol w/v 28 Conversation Conversation RCL v/w MemScan w/v RCL RCL Last No w / v Back to FCN 1 Note: The function menu is not available in conversation mode. In standby mode, the "STO" or "END" key can be used to exit from the function mode. FCN 1 : Telephone Number Function (Standby & Conversation) Press "FCN" and "1". Tel:123 4567890 Function: When the user enters the "FCN" key followed by "1", the phone enters "Own Telephone Number Display mode". When first pressing either key, it will display the current NAM number and telephone number. 1: 123 4567890 Press */# key 2: 321 7890456 In order to exit from this mode, press the "STO, " "END, " or "CLR" key. 29 If the phone is locked, this operation is ignored. Note: This function operates even if the phone is in conversation mode. To exit from conversation mode, press "STO" or "CLR". FCN 2: Input/Edit Alphabet Name And Number Direct Operation: (number) +FCN + 2 +(alphabet)+ STO "FCN" + "STO" or "STO" + "XX" (0139 only) in Standby mode only Display: When FCN + 2 is pressed: Alpha Input is displayed. Function: A maximum of 11 alphanumeric characters can be stored into the name area and up to 32 digits can be stored into the number area. The characters table is: KEY CHARACTERS 1QZ_ 1 2ABC 2 3DEF 3 4GHI 4 5J KL 5 6MNO6 7P RS 7 8T UV 8 9WXY 9 0O *. #- , ! " ? * # 30 Example: Press "2" key once Press "2" key twice Press "2" key three times Press "2" key four times Press "2" key five times = "A" = "B" = "C" = "2" = "A" To complete your selection, press the key for one (1) second or press another key. If a key must be repeated, the user must press the key for one (1) second in order to advance to the next character. Example (a): Input new name and number Name "DAVE" / Number "2133932111" Operation Enter number FCN + 2 One second later 3 once 2 once 8 three times 3 twice FCN+STO or STO+XX (01 to 39) Display 213 3932111 Alpha Input ??: ALPHA D ALPHA DA ALPHA DAV ALPHA DAVE ALPHA Stored Addr. XX 31 Note: · If a character is repeated, the key must be held for one (1) second in order to advance to the next character. · "ALPHA" indicates that the phone is in the Input/ Edit mode. · If the call restriction level is Recall 1-39 or Receive Only, this function is not available. The following message will appear on the display when call restriction is selected: Alpha N. A. Example (b): Add name to a stored number Address 12 Number "7112340" Add name "CEW" Display 12: 7112340 7112340 Alpha Input 12: ALPHA Operation RCL 12 CLR to exit RCL mode FCN + 2 One second later Enter alphabet CEW ALPHA 32 STO STO 7 112340_ Stored Addr. 12 Example (c): Edit a stored name and number Address 28 Operation RCL 28 CLR to exit RCL mode FCN + 2 One second later Edit name STO Edit Number STO Number "4975646" Display 28:MELC 4975646 4975646 Alpha Input 28: MELCO ALPHA Name "MELCO" M-CEW ALPHA 4 974656_ Stored Addr. 28 Function: A new character and number can be added to the last character of the stored name and number in this mode. 33 To delete the last character and number, press the "CLR" key. Note: · · During this editing mode no calls can be made. If all characters and numbers of the selected address are deleted by the "CLR" key, press the "STO" key to exit this mode. The following message is displayed: Erased Addr. 09 FCN 3: Automatic Redialing Direct Operation: FCN + 3 (Standby only) Redial ON Press */# key Redial OFF Function: When you enter "FCN" followed by "3", the phone enters the "Automatic Redial ON/OFF" mode and shows the current setting. The ON/OFF setting can be selected by pressing the "*" or "#" keys. In case of "Redial ON", the Automatic Redial function is active. The phone will attempt automatic retry 10 times with a three (3) second interval between each try when unable to access the cellular system. [. . . ] While speaking directly into the mouthpiece, position the antenna up and over your shoulder. Holding the antenna affects call quality and may cause the phone to operate at a higher power level than needed. Antenna Care and Replacement Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Non-approved antennas, modifications, or attachments could impair call quality, damage the phone, and violate FCC regulations. 52 Driving Check the laws and regulations on the use of cellular telephones in the areas where you drive. [. . . ]