User manual MITSUBISHI CP9800DW-S

[. . . ] DIGITAL COLOR PRINTER MODEL CP9800DW-S OPERATION MANUAL THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL COLOR PRINTER. Hereby, Mitsubishi Electric Corporation, declares that this digital color printer is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. This digital color printer complies with the requirements of the EC Directive 89/336/EEC, 93/68/EEC and 2006/95/EC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. [. . . ] See page 17. 7PAPER/INK RIBBON INDICATOR ( CONTENTS ) E FEET These feet can be removed. NOTE When this printer is turned on, the indicators start illuminating in sequence. The printer is ready for use when the POWER and READY buttons are lit. When an error concerning the ink ribbon or print paper occurs, this indicator illuminates or blinks. See page 17. 8DATA INDICATOR ( ) This indicator blinks during data transfer. It illuminates during printing. 9 READY INDICATOR ( ) This indicator illuminates when this unit is ready to accept the data. It blinks during print canceling procedure. 7 FEATURES & FUNCTIONS SIDE AND REAR PANEL PRECAUTIONS 1 3 2 3 FEATURES 4 5 CONNECTIONS PREPARATION (LEFT SIDE) 1 USB TERMINAL Use to connect the USB cable. See page 9. (REAR) 3 HANDLE FOR TRANSPORTING When transporting this unit, hold this handle and the upper front part of this unit. 2 DIP SWITCHES Use to set various functions of this unit. See page 10. 4 POWER SOCKET (AC LINE) Use to connect the provided power cord. Insert the cord firmly. 5 POWER SWITCH Use to switch the power ON and OFF. REMOVING THE FEET 1. Make sure that the bottom of the door does not touch the table when opened and that the printer does not fall from the table. TROUBLESHOOTING OTHERS Place the printer so that the door does not touch the corner of the table. CONTENTS INSTALLING THE PAPER CATCHER Hook the paper catcher by its latches. When using the print paper of 13x18(5x7"), 15x20(6x8") or 15x23(6x9"), do not install the paper catcher. A. B. C. Holes for 10 x 15 size paper (Paper width : 152 mm) 8 CONNECTIONS CONNECTION WITH USB DATA SIGNAL EQUIPMENT 2 CONNECTING TO PERSONAL COMPUTER (EXAMPLE) Connect this unit to a personal computer as shown below. PRECAUTIONS To USB port FEATURES To USB port CONNECTIONS PREPARATION Personal computer Digital color printer NOTE A USB cable is not supplied with this unit. Use the USB 2. 0 certified cable of 2 m or less in length. TROUBLESHOOTING OTHERS CONTENTS 9 CONNECTIONS SETTING OF DIP SWITCHES 2 SETTING DIP SWITCHES All the switches are set to OFF at the time of shipment from the factory. Turn off the power before changing the DIP switch settings. PRECAUTIONS OFF ON Switch No. Setting Function 1 OFF Auto feed & cut mode When the door is closed after the print paper is installed with this unit powered on, this unit automatically carries out paper feed & cut operation. ON 12345678 FEATURES CONNECTIONS PREPARATION TROUBLESHOOTING OTHERS CONTENTS 10 BEFORE OPERATION Before printing, PRECAUTIONS 1 Install the print paper to this unit. (page 14-15) INSTALLATION OF PRINT PAPER Spacers 2 For the usage of the spacers, see the Quick Setup Guide. Remove the cushions put between the paper flange and spacer when using the spacers. When you remove the spacers from the paper flanges, follow the above procedure in reverse. Paper flange FEATURES CONNECTIONS PREPARATION 1 Attach the supplied paper flanges to both sides of the print paper. When you pinch the latches on the paper flange, the stoppers retract into the shaft. Make sure that the flanges are attached to the print paper securely, and release the latches. Sticker · · CAUTION When placing the print paper, remove one flange and keep the print paper upright on its side with no flange. This may cause injury. TROUBLESHOOTING · · · OTHERS CONTENTS INCORRECT NOTE · · Do not touch the thermal head. [. . . ] If the unit is transported with the package unit more than one round trip, it may not be guaranteed. Pack the unit with all the accessories (ink ribbon, print paper, ink cassette, and paper flanges) removed. 2. Turn off the power after the PAPER/INK RIBBON indicator blinks. After removing all the accessories, close the door with the printer's power on. After the PAPER/INK RIBBON indicator blinks, turn the power off. CONTENTS 3. [. . . ]