User manual MITSUBISHI CP9810DW

[. . . ] DIGITAL COLOR PRINTER MODEL CP9810DW OPERATION MANUAL THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL COLOR PRINTER. Hereby, Mitsubishi Electric Corporation, declares that this digital color printer is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. INFORMATION This Class A digital apparatus complies with Canadian ICES-003. PRECAUTIONS WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: Use the included AC power cord so as not to interfere with radio and television reception. If you use other cables, it may cause interference with radio and television reception. FEATURES CONNECTIONS PREPARATION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute the risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. [. . . ] See page 9. (REAR) 3 HANDLE FOR TRANSPORTING When transporting this unit, hold this handle and the upper front part of this unit. 2 DIP SWITCHES Use to set various functions of this unit. See page 10. 4 POWER SOCKET (AC LINE) Use to connect the provided power cord. Insert the cord firmly. 5 POWER SWITCH Use to switch the power ON and OFF. REMOVING THE FEET 1. Make sure that the bottom of the door does not touch the table when opened and that the printer does not fall from the table. TROUBLESHOOTING OTHERS Place the printer so that the door does not touch the corner of the table. CONTENTS INSTALLING THE PAPER CATCHER Hook the paper catcher by its latches. When using the print paper of 13x18(5x7"), 15x20(6x8") or 15x23(6x9"), do not install the paper catcher. A. Holes for 9 x 13 size paper (Paper width: 127 mm) Holes for 10 x 15 size paper (Paper width: 152 mm) B. C. 8 CONNECTIONS CONNECTION WITH USB DATA SIGNAL EQUIPMENT 2 CONNECTING TO PERSONAL COMPUTER (EXAMPLE) Connect this unit to a personal computer as shown below. PRECAUTIONS FEATURES To USB port To USB port CONNECTIONS PREPARATION Personal computer NOTE Digital color printer A USB cable is not supplied with this unit. Use the USB 2. 0 certified cable of 2 m or less in length. TROUBLESHOOTING OTHERS CONTENTS 9 CONNECTIONS SETTING OF DIP SWITCHES 2 SETTING DIP SWITCHES All the switches are set to OFF at the time of shipment from the factory. Turn off the power before changing the DIP switch settings. PRECAUTIONS OFF ON Switch No. Setting Function 1 OFF Auto feed & cut mode When the door is closed after the print paper is installed with this unit powered on, this unit automatically carries out paper feed & cut operation. ON 12345678 FEATURES CONNECTIONS PREPARATION TROUBLESHOOTING OTHERS CONTENTS 10 BEFORE OPERATION Before printing, PRECAUTIONS 1 Install the print paper to this unit. (See page 14-15. ) INSTALLATION OF PRINT PAPER Spacers 2 For the usage of the spacers, see the Quick Setup Guide. Remove the cushions put between the paper flange and spacer when using the spacers. When you remove the spacers from the paper flanges, follow the above procedure in reverse. Paper flange FEATURES CONNECTIONS PREPARATION 1 Attach the supplied paper flanges to both sides of the print paper. When you pinch the latches on the paper flange, the stoppers retract into the shaft. Make sure that the flanges are attached to the print paper securely, and release the latches. Sticker · · CAUTION When placing the print paper, remove one flange and keep the print paper upright on its side with no flange. This may cause injury. TROUBLESHOOTING · · · OTHERS CONTENTS INCORRECT NOTE · · Do not touch the thermal head. Fingerprints or dust on the thermal head will degrade the print quality. Fingerprints or dust on the paper's surface may degrade print quality and cause paper jams. CORRECT 11 BEFORE OPERATION 2 Press the POWER switch on the rear panel to turn on the power. PRECAUTIONS POWER switch 3 After the mechanical initialization is completed, press the DOOR OPEN button to open the door. Take the ink cassette in the printer out. FEATURES CONNECTIONS PREPARATION 4 Install the print paper into the unit. Make sure to install the print paper firmly. If it is dropped along the ditches, the unit or accessories may be damaged. · CAUTION Do not touch the thermal head right after printing because it is extremely hot. NOTE Note that the thermal head is quite sensitive to static electricity. When you touch the thermal head while carrying static electricity on your body, the thermal head may be damaged. Thermal head (inside) TROUBLESHOOTING · OTHERS 5 Remove the sticker, insert the print paper between the rollers as shown right, and feed the print paper until it reaches the black cover. · Remove the sticker before inserting the print paper between rollers. Roller Direction of paper insertion Print paper CONTENTS · · · NOTE When taking the print paper out, pull it up toward you. [. . . ] Pack the unit with all the accessories (ink ribbon, print paper, ink cassette, and paper flanges) removed. 2. Turn off the power after the PAPER/INK RIBBON indicator blinks. After removing all the accessories, close the door with the printer's power on. After the PAPER/INK RIBBON indicator blinks, turn the power off. 3. If the ink ribbon, print paper, or ink cassette can not be taken out, consult with your dealer. 20 CLEANING Cleaning as indicated below will help maintain stable printer operation and extend the printer's life. PREPARATIONS FOR CLEANING 1 Press the POWER switch on the rear panel to turn on the power. [. . . ]