User manual MITSUBISHI DIAMOND PLUS 200

[. . . ] AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR MODEL NSH1117STTKW USER'S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor. Internet Home Page: http://www. mitsubishi-display. com/ Supplying Windows 95/98 INF File download service, new product information, etc. ® -2- CONTENTS ENGLISH 1. 6 CAUTION The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. Do not remove the monitor cabinet as this can expose you to very high voltages and other hazards. 1. 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] OK OK 1. 8 Tilt/Swivel Base The monitor comes with a tilt/swivel base. This enables you to position the monitor at the best angle and tilt for maximum viewing comfort. Screen Position Adjustment Adjust the tilt and rotation of the monitor by placing your hands at opposite sides of the case. You can adjust the monitor 90 degrees right or left, 10 degrees up or 5 degrees down, as shown below. See Section 5. TROUBLESHOOTING If the problem persists. Call for your authorized MITSUBISHI Product Support. 10 90 90 5 Figure 2 CAUTION Keep your fingers away from the pivot area of the tilt/swivel base. -8- 2 PART NAME 2. 1 Control Names See Figures 3 and 4 for the location of the user controls, indicator and connectors. Each part is identified by number and is described individually. ENGLISH FRONT REAR D-SUB D-SUB SIGNAL-A SIGNAL-B 9 Figure 3 Figure 4 2. 2 Function 7. UPSTREAM PORT: To connect to a USB equipped computer for Monitor Control Function. 1. POWER-ON INDICATOR: This indicator illuminates green when AC power is on, and illuminates amber when the monitor is in the power management modes. INPUT CONNECTOR SELECT/OSD OFF BUTTON: · Without OSD screen, push to select the signal input connector, SIGNAL A or B. FUNCTION ADJUST BUTTONS: Push the adjust buttons to adjust the image on the screen. -9- 3 INSTALLATION AND CONNECTION On the back of the monitor three plug-in connections are provided: AC power connector for the AC input, and two DB9-15P connectors for video signal input. 3. 1 AC Power Connection 3. 2. 2 Connecting to An Apple Macintosh Computer Figure 6 shows the SC-B104 cable and AD-A205 Adapter(option) to the video port in an Apple Macintosh. Set the DIP switches of Macintosh Adapter according to the setting chart. (See Section 7. 3 Optional Macintosh Adapter ADA205 Settings) Connect the 15-pin (DB-15P) end of the AD-A205 Adapter to the straight 15-pin connector on the Macintosh video port on the computer or on the video board. Connect the sub-miniature 15-pin (DB9-15P) end of the AD-A205 Adapter to the SC-B104 cable. Connect the other end of the SC-B104 cable to the DB9-15P receptacle on the back of the monitor. After using the system, power off the monitor, then the Macintosh. D-SUB D-SUB One end of the AC power cord is connected to the AC power connector on the back of the monitor. The other end is plugged into a properly grounded three-prong AC outlet. The monitor's auto-sensing power supply can automatically detect 100-120V AC or 220-240V AC and 50 or 60Hz. 7. The DB9-15P(VGA) connector is provided for compatible analog RGB outputs from your computer. Apple Macintosh computers can also be interfaced with using the optional Mitsubishi Macintosh adapter AD-A205. 3. 2. 1 Connecting to Any IBM VGA Compatible System Figure 5 shows the SC-B104 cable connection to the Video Graphics Array (VGA) port in an IBM Personal System/2® series, or any VGA compatible system. Connect the one end of the SC-B104 cable to the DB9-15P connector on the VGA controller card. [. . . ] In this case, please select other resolution, or other vertical refresh timing. · Make sure you wait a few seconds after adjusting the size of the image before changing or disconnecting the signal. · "VIDEO LEVEL" is not at the appropriate position for your graphics adapter output. (0. 7v or 1. 0Vp-p). · Front (OSD) · Front (OSD) Display is dark or too bright · Front (OSD) - 17 - PROBLEM ITEMS TO CHECK · Thin vertical black lines on one or both sides of the screen. [. . . ]