User manual MITSUBISHI DIAMOND PRO 2040U

[. . . ] AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR MODEL NSB1107STTUW USER'S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor. Internet Home Page: http://www. mitsubishi-display. com/ Supplying Windows 95/98 INF File download service, new product information, etc. ® -2- CONTENTS ENGLISH 1. 6 CAUTION The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. Do not remove the monitor cabinet as this can expose you to very high voltages and other hazards. 1. 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect the other end of the SC-B104 cable to the DB9-15P receptacle on the back of the monitor. After using the system, power off the monitor, then the computer. 4. HD VD D-SUB R Macintosh Adapter AD-A205 (Option) Power Cord Cable SC-B104 Figure 6 Computer D-SUB BNC · A B 1 2 R G B COMP. HD VD VGA Compatible System DB9-15P · For the Apple Macintosh Computers having a VGA compatible port, steps 2 through 4 are not necessary. In case of Apple Macintosh G3 series, use "Control Panel" of "Apple Menu" when selecting a resolution. If select the resolution from "Control Bar", no screen may be displayed and the computer may freeze. Power Cord Cable SC-B104 Figure 5 CAUTION The socket-outlet shall be installed near the equipment and shall be easily accessible. Méme si le moniteur est mis hors tension il reste toujours alimenté. La prise secteur devrait ainsi ètre facilement accssible en cas d'urgence. - 10 - 3. 2. 3 Connecting to a Unix Workstation & Third Party Graphics Card Figure 7 shows the SC-B104 or 75 coaxial cable (not supplied) connection to the graphics video card (PC-CAD and workstation). Connect one end of the SC-B104 cable or the 75 coaxial cable to the output connector on the computer, or on the video board. Connect the other end of the SC-B104 cable or the 75 coaxial cable to the DB9-15P receptacle or the BNC receptacles on the back of the monitor. After using the system, power off the monitor, then the computer. 3. 2. 4 BNC Connection (1) COMPOSITE SYNC ON GREEN VIDEO SIGNAL (3 wires): Connect the R, G and B video signals to the BNC connectors on the back of the monitor. BNC A B 1 2 R G B COMP. 5. (2) EXTERNAL COMPOSITE SYNC SIGNAL(4 wires): Connect the R, G and B video signals and the Composite sync signal to BNC connectors on rear panel, respectively. BNC A D-SUB B 1 2 R G B COMP. HD VD High Resolution Graphic Video Card D-SUB BNC R G B COMP. HD VD High Resolution Graphic Video Card coaxial cable Cable SC-B104 Power Cord 75 (3) SEPARATE HORIZONTAL AND VERTICAL SYNC SIGNALS (5 wires): Connect the R, G and B video signals and the horizontal and vertical sync signals to the BNC connectors on the rear panel. BNC Figure 7 A B 1 2 R G B COMP. HD VD 3. 3 USB System Basic Application FRONT Power Cord BACK D-SUB BNC A B 1 2 R G B COMP. HD VD Downstream Ports Downstream Port D-SUB A B 1 R G BNC B COMP. HD VD USB Cable Upstream Ports 2 Signal Cable Signal Cable NOTE USB Cable Computer Scanner The computer is required to have Windows® 98 or later installed and USB functions. When connecting one computer, either Upstream port A or B is available. The Upstream port is automatically matched with the active video input. Keyboard Camera - 11 - 3. 4 Installation of USB Function The following procedure permits your computer to recognize or "enumerate"(A USB term) the Mitsubishi USB HUB. Start "Enumeration" from the Windows® Desktop. (a) Disconnect and connect the USB cable to the upstream port of the display monitor. (b) Cycle power of the display monitor off then on. NOTE NOTE If the mark appears with "Generic USB HUB", then enumeration was unsuccessful. Select "Generic USB HUB" marked with mark and click "Remove" and "Refresh". [. . . ] No operation of the USB devices · Confirm that Windows98 is installed into the computer. · Disconnect all the cables connected to theUpstream ports and re-connect then. · Select the Upstream port by using the OSD screen, "Upstream port selection" · On the OSD screen, the Upstream port to which the USB device you want to use is connected is not colored by blue. - 19 - PROBLEM ITEMS TO CHECK · Thin vertical black lines on one or both sides of the screen. This minor condition is caused by grille element overlap which can occur during shipping. [. . . ]