User manual MITSUBISHI DIAMOND PRO 2060U

[. . . ] AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR USER S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor. Internet Home Page: http://www. necmitsubishi. com/ Supplying Windows 95/98/2000 INF File download service, new product information, etc. ® RADIO INTERFERENCE REGULATIONS STATEMENT FOR U. S. A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] TROUBLESHOOTING If the problem persists. Call for your authorized Product Support. Tilt/swivel base Figure 2 CAUTION Keep your fingers away from the pivot area of the tilt/swivel base. -1-4 - 2 PART NAME 2. 1 Control Names See Figures 3 and 4 for the location of the user controls, indicator and connectors. Each part is identified by number and is described individually. ENGLISH FRONT SIGNAL A/B OSD OFF SIGNAL-B SIGNAL-A REAR Figure 3 Figure 4 2. 2 Function 5. FUNCTION ADJUST BUTTONS: Push the adjust buttons to adjust the image on the screen. 1. POWER-ON INDICATOR: This indicator illuminates green when AC power is on, and illuminates orange when the monitor is in the power management modes. INPUT CONNECTOR SELECT/OSD OFF BUTTON: · Without OSD screen, push to select the signal input connector, SIGNAL A or B. NOTE If only one input is used, the monitor will select it automatically. USB DOWNSTREAM PORTS: To connect to USB equipped peripherals, e. g, USB cameras, keyboards, printers, etc. - 1-5 - 3 INSTALLATION AND CONNECTION On the back of the monitor three kinds of plug-in connections are provided: AC power connector for the AC input, two DB9-15P connectors for video signal input, and USB ports for USB communication. 3. 1 AC Power Connection 3. 2. 2 Connecting to An Apple Macintosh Computer Figure 6 shows the SC-B110 cable and AD-A205 Adapter(option) to the video port in an Apple Macintosh. Set the DIP switches of Macintosh Adapter according to the setting chart. (See Section 7. 3 Optional Macintosh Adapter ADA205 Settings) Connect the 15-pin (DB-15P) end of the AD-A205 Adapter to the straight 15-pin connector on the Macintosh video port on the computer or on the video board. Connect the sub-miniature 15-pin (DB9-15P) end of the AD-A205 Adapter to the SC-B110 cable. Connect the other end of the SC-B110 cable to the DB9-15P receptacle on the back of the monitor. After using the system, power off the monitor, then the Macintosh. 3. One end of the AC power cord is connected to the AC power connector on the back of the monitor. The other end is plugged into a properly grounded three-prong AC outlet. The monitor's auto-sensing power supply can automatically detect 100-120V AC or 220-240V AC and 50 or 60Hz. 7. The DB9-15P(VGA) connector is provided for compatible analog RGB outputs from your computer. Apple Macintosh computers can also be interfaced with using the optional Mitsubishi Macintosh adapter AD-A205. 3. 2. 1 Connecting to Any IBM VGA Compatible System Figure 5 shows the SC-B110 cable connection to the Video Graphics Array (VGA) port in an IBM Personal System/2® series, or any VGA compatible system. Connect the one end of the SC-B110 cable to the DB9-15P connector on the VGA controller card. Connect the other end of the SC-B110 cable to the DB9-15P receptacle on the back of the monitor. After using the system, power off the monitor, then the computer. SIGNAL-B SIGNAL-A Apple Macintosh Computer 1 D-SUB15P 502A-DA NO 654321 Cable SC-B110 IHSIBUSTIM 2 DB9-15P Macintosh Adapter AD-A205 (Option) Figure 6 SIGNAL-B SIGNAL-A NOTE · For the Apple Macintosh Computers having a VGA compatible port, steps 2 through 4 are not necessary. [. . . ] The resolution does not change with the computer powered on when you set the dip switches. Set the dip switches by a pointed article like a pencil or ball point pen to touch end of the switch groove. Registration To learn about other special offers, register online at, http://www. necmitsubishi. com/productregistration Limited Warranty NEC-Mitsubishi Electronics Display of America, Inc. (hereinafter "NMD-A") warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NMD-A's sole option) any part of the enclosed unit which proves defective for a period of three (3) years from the date of first consumer purchase. Replacement parts or unit may be new or refurbished and will meet specifications of the original parts or unit. [. . . ]