User manual MITSUBISHI DIAMOND PRO 710

[. . . ] AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR Model NFF8705STTKW USER'S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor. Internet Home Page: http://www. mitsubishi-display. com/ Supplying Windows 95/98 INF File download service, new products information, etc. - ii - RADIO INTERFERENCE REGULATIONS STATEMENT FOR U. S. A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Avoid putting the monitor into any enclosure that does not have adequate ventilation. · Avoid exposing the monitor to rain, excessive moisture, or dust, as this can cause a fire or shock hazard. · Avoid placing the monitor, or any other heavy object, on the power cord. N. I. Fh(kHz) Fv (Hz) 31. 5 60. 0 37. 5 75. 0 49. 7 74. 5 46. 9 75. 0 56. 5 70. 0 68. 7 75. 1 60. 0 75. 0 80. 0 75. 0 Power Management Function The monitor has a power management function which reduces the power consumption of the monitor when not in use. Check your computer manual for the instructions for setting the power saving timing. Mode Power Power On Indicator 1. 6 Cleaning Your Monitor When cleaning the monitor, please follow these guidelines: · Always unplug the monitor before cleaning. Normal Stand-By Suspend Off 105 W 80 W 15 W 8W Green Red Red Red · Wipe the screen and cabinet front and sides with a soft dry cloth. · If the screen requires more than dusting, apply a household window cleaner to a soft cloth to clean the monitor screen. · Do not spray directly on the screen as excess cleaner may drip into the monitor causing damage. CAUTION 1. 4 DDC The monitor includes the DDC1 and DDC2B feature more commonly known as "Plug & Play". DDC (Display Data Channel) is a communication channel over which the monitor automatically informs the computer system about its capabilities (e. g. DDC is routed through previously unused pins of the 15-pin VGA connector. The system will perform "Plug and Play" feature if both, monitor and computer, implement the DDC protocol. When a Plug & Play computer starts, it identifies the monitor and loads the appropriate driver automatically. If the computer does not have the driver installed, a dialog box will appear asking where the information can be found. The latest drivers may be downloaded from the "Support" section of the Mitsubishi website located at: http://www. mitsubishi-display. com/ Do not use benzene, thinner or any volatile substances to clean the unit as the finish may be permanently marked. Never leave the monitor in contact with rubber or vinyl for an extended time period. -3- 1. 7 Unpacking 1. 9 Quick Operation Chart To summarize the steps in connecting your computer with the color monitor and setting the necessary controls and switches, refer to the chart below. After you unpack the box you should have all of the items indicated in Figure 1. 1 2 3 Connect the color monitor and computer with the necessary cords and cables. INSTALLATION AND CONNECTION 4 5 Turn on the color monitor. Figure 1 1. 1. 8 Color Monitor AC Power Cord User's Guide (this document) Warranty-Card Questionnaire-Card Tilt/Swivel Base See Section 4. OSD(On Screen Display) FUNCTIONS OK OK If a problem appears. This enables you to position the monitor at the best angle and tilt for maximum viewing comfort. Screen Position Adjustment Adjust the tilt and rotation of the monitor by placing your hands at opposite sides of the case. You can adjust the monitor 90 degrees right or left, 15 degrees up or 5 degrees down, as shown below. If the problem persists. Call for your authorized Mitsubishi Product Support. 15 90 90 5 Figure 2 CAUTION Keep your fingers away from the pivot area of the tilt/swivel base. -4- 2 PART NAME 2. 1 Control Names See Figures 3 and 4 for the location of the user controls, indicator and connectors. Each part is identified by number and is described individually. FRONT REAR Figure 3 2. 2 Function Figure 4 1. [. . . ] ENG. . . . . . English, ESP. . . . . . Spanish, GER. . . . . . German, FRA. . . . . . French -8JPN. . . . . . Japanese, 5 TROUBLESHOOTING Before calling your Authorized Product Support, please check that the items below are properly connected or set. In case of using a non-standard signal, please check the pin assignments and the signal timing of your computer with the specification outlined in 6. PROBLEM LED On (Green) LED Off No picture LED On (Red) ITEMS TO CHECK · Contrast and brightness controls. · Front (OSD) · Front · Rear · · · · · · · · Rear Check the graphics adapter and cables Computer Press any key on the keyboard or move the mouse. [. . . ]