User manual MITSUBISHI DIAMOND PRO 900

[. . . ] AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR MITSUBISHI MODEL NFJ9905SKHUW USER'S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor. ENGLISH CAUTION The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. Do not remove the monitor cabinet as this can expose you to very high voltages and other hazards. ANMERKUNG: Dieser Monitor erfüllt die Anforderungen der deutschen Ergonomie-Norm ZH1/ 618/10. 80 bei Verwendung der beiden folgenden Timing: Auflösung Videoeingang 1280x1024 Analog RGB, 0. 7Vs-s fH(kHz) fv(Hz) Interlace/Non-Interlace 91. 1 85. 0 Non-Interlaced Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf dunklerem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast). [. . . ] After using the system, power off the monitor, then off the computer. Computer VGA Compatible System D-SUB BNC R G B COMP. HD VD DB9-15P DB9-15P Power Cord CABLE SC-B102 Figure 5. CAUTION The socket-outlet shall be installed near the equipment and shall be easily accessible. During servicing, disconnect theshall be installed near the equipment and shall be easily accessible. MémeDuring servicing, disconnect the plug reste toujours alimenté. La prise secteur devrait ainsi si le moniteur est mis hors tension il from the socket-outlet. Méme si le moniteur est mis hors tension il reste toujours alimenté. La prise secteur devrait ainsi ètre facilement accssible en cas d'urgence. - 1-13 - CAUTION ENGLISH 3. 2. 2 Connecting to An Apple Macintosh Computer Figure 6 shows the SC-B102 cable and AD-A205 Adapter to the video port in an Apple Macintosh. Set the DIP switches of Macintosh Adapter according to the setting chart. (See 7. 3 Macintosh Adapter AD-A205 settings) Connect the 15-pin (DB-15P) end of the AD-A205 Adapter to the straight 15-pin connector on the Macintosh video port on the CPU or on the video board. Connect the sub-miniature 15-pin (DB9-15P) end of AD-A205 Adapter to the SC-B102 cable. Connect the other end of the SC-B102 cable to the DB9-15P receptacle on the back of the monitor. After using the system, power off the monitor, then off the Macintosh. Computer Apple Macintosh Computer Macintosh Adapter AD-A205 D-SUB BNC R G B COMP. HD VD DB-15P DB9-15P Power Cord CABLE SC-B102 Figure 6. 3. 2. 3 Connecting to a Unix Workstation & Third Party Graphics Card Figure 7 shows the SC-B102 or "75 card (PC-CAD and workstation). " coaxial cable (not supplied) connection to the graphics video Power off, both the monitor and the computer. Connect one end of the SC-B102 cable or the "75 " coaxial cable to the output connector on the CPU, or on the video board. Connect the other end of the SC-B102 cable or the "75 " coaxial cable to the DB9-15P receptacle or the BNC receptacles on the back of the monitor. After using the system, power off the monitor, then off the computer. High Resolution Graphic Video Card High Resolution Graphic Video Card D-SUB BNC R G B COMP. HD VD Power Cord "75 " coaxial cable Please see next page about BNC connection. - 1-14 - ENGLISH 3. 2. 4 BNC Connection (1) IN CASE OF A COMPOSITE SYNC ON GREEN VIDEO SIGNAL (SYNC ON GREEN): Connect the R, G and B video signals to the BNC receptacles on the back of the monitor. D-SUB BNC R G B COMP. HD VD (2) IN CASE OF EXTERNAL COMPOSITE SYNC SIGNAL: Connect the R, G and B video signals and the Composite sync signal to BNC receptacles on rear panel, respectively. D-SUB BNC R G B COMP. HD VD (3) IN CASE OF SEPARATE HORIZONTAL AND VERTICAL SYNC SIGNALS: Connect the R, G and B video signals and the horizontal and vertical sync signals to the BNC receptacles on the rear panel. D-SUB BNC R G B COMP. [. . . ] · Disconnect all the cables connected to the Upstream ports and re-connect then. - 1-33 - ENGLISH PROBLEM Black vertical lines are visible on the screen. ITEMS TO CHECK · Thin vertical black lines on one or both sides of · the screen. This minor condition is caused by grille element overlap which can occur during shipping. We suggest slapping the cabinet sides with an open hand after the monitor is warm. If this fails, position an open white window over the affected area of the screen and maximize the brightness and contrast controls. [. . . ]