User manual MITSUBISHI DIAMOND SCAN 90E

[. . . ] MITSUBISHI AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR MODEL FFT9905SKHFW USER'S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor. CAUTION The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. Do not remove the monitor cabinet as this can expose you to very high voltages and other hazards. Trademark IBM, PC, PS/2, PS/V, Personal System/2 are registered trademarks of International Business Machines Corp. UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. [. . . ] DDC (Display Data Channel) is a communication channel over which the monitor automatically informs the host system about its capabilities (e. g. DDC is routed through previously unused pins of the 15-pin VGA connector. The system will perform "Plug and Play" feature if both, monitor and host, implement the DDC protocol. 1. 5 Location Considerations When setting up and using the monitor, keep the following in mind: * For optimum viewing, avoid placing the monitor against a bright background or where sunlight or other light sources may reflect on the display area of the monitor; place the monitor just below eye level. Place the monitor away from strong magnetic or electromagnetic fields, such as high capacity transformers, electric motors, large current power lines, steel pillars, etc. . . . Allow adequate ventilation around the monitor so the heat from the monitor can properly dissipate. Avoid putting the monitor into any enclosure that does not have adequate ventilation. Avoid exposing the monitor to rain, excessive moisture, or dust, as this can cause a fire or shock hazard. Avoid placing the monitor, or any other heavy object, on the power cord. When transporting the monitor, handle it with care. * * * * * CAUTION Keep your fingers away from the pivot area of the tilt/swivel base. 1. 6 Cleaning Your Monitor When cleaning the monitor, please follow these guidelines: * * * Always unplug the monitor before cleaning. If the screen requires more than dusting, apply a household window cleaner to a soft cloth to clean the monitor screen. CAUTION Do not use benzene, thinner or any volatile substances to clean the unit as the finish may be permanently marked. Never leave the monitor in contact with rubber or vinyl for an extended time period. 8 1. 7 Unpacking After you unpack the box you should have all of the items indicated in Figure 1. Save the box and packing materials in case you ship or transport the monitor. 1 2 3 4 5 20 -A AD O N 1 2 5 6 M O DE L FF T99 05 SK HK W 1. Warranty-Set Figure 1. M IT SU 3 4 5 6 BI SH I M M I e e H 0 9 IS n n B a U c S S d IT n o o e m ia Guid D r's G s U U e 1. 8 Tilt/Swivel Base The monitor comes with a tilt/swivel base. This enables you to position the monitor to the best angle and tilt for maximum viewing comfort. Screen Position Adjustment Adjust the tilt and rotation of the monitor by placing your hands at opposite sides of the case, as shown in Figure 2. You can adjust the monitor 45 degrees right or left, 10 degrees up or 5 degrees down, as shown below. 10 45 45 5 Figure 2. 9 1. 9 Quick Operation Chart To summarize the steps in connecting your computer and adapter with Diamond Scan 90e color monitor and setting the necessary controls and switches, refer to the chart below. Connect the power cord to the Diamond Scan 90e color monitor and the signal cable between the Diamond Scan 90e and the graphics adapter. See 2. 1 AC Power Connection 2. 2 Signal Cable Connection Turn on the computer. Turn on the Diamond Scan 90e color monitor. Set the controls and switches. See 3. TROUBLESHOOTING If the problem persists. Call for your authorized MITSUBISHI Product Support at 1-800-344-6352. 10 2 CONNECTING THE MONITOR On the back of the monitor are four plug-in connections: one for the AC power cord, DB9-15P connector, BNC connector for video and a DIN-8P connector for the optional USB-unit. 2. 1 AC Power Connection One end of the AC power cord is connected into the AC power connector on the back of the monitor. The other end is plugged into a properly grounded three-prong AC outlet. The monitor's auto-sensing power supply can automatically respond to the power supply input of 100240V AC and 50/60Hz. 2. 2 Signal Cable Connection The attached video signal cable provides a DB9-15P connector for the VGA compatible analog RGB outputs on your computer. [. . . ] In case of using a non-standard signal, please check the pin assignments and the signal timing of your computer with the specification outlined in SPECIFICATION 6 and APPENDIX 7. PROBLEM LED On-Green LED Off ITEMS TO CHECK · Contrast and brightness controls. LOCATION No picture · · · · · · LED On-Amber · Un-stable · picture Abnormal picture No green color with BNC · · · Display is missing, center shifts, or too small or too · large of a display size · Front (Adjust to the maximum brightness or push the reset button) · Front Power switch. · Check the graphics BNC cables are misconnected or the green adapter and cables cable is disconnected. [. . . ]