User manual MITSUBISHI DX-TL2500E

[. . . ] DIGITAL RECORDER OTHERS INSTALLATION AND OPERATION MANUAL MODEL DX-TL2500E THIS INSTRUCTION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL RECORDER. 1 ENGLISH Features Built-in duplex 16 channel multiplexer The screen mode can be switched on the monitor such as single screen, split4, split9 and split16 screen and sequential screen, split4 sequential screen and split9 sequential screen. ( see page 37) The unit is equipped with the 2 type-output connector to display the different mode split screen on the each of different monitors. Live picture from all cameras can be recorded continuously while the recording of desired camera is played back. [. . . ] Press the SET UP button } <SETTINGS> } <INITIAL SET UP/INFORMATION> } Select "FIFO OVERWRITE MODE" in the <HDD SETTINGS> screen. Turn the SHUTTLE ring clockwise twice when the cursor is on the left next to "FIFO OVERWRITE MODE". The first turn inverts the "OFF" setting display, and the second makes it flash with a red background. #1 #2 #1 #1. Appears when "ARCHIVECOPY" is set to ID4ID5 on the screen. #2. Appears when "PARTITION" ("LONG PRE-ALARM") is set and "ARCHIVECOPY" is set to ID4ID5 respectively on the screen. Setting ( default : "OFF" ) "ON" : Plays back the video in the single screen sequential mode. "OFF" : Does not play back the video in the single screen sequential mode. Playback is performed during camera sequential play at an interval of 25P. PLAY button)( see "Changing playback intervals, pages 69, 70). 1. Press the SET UP button } <SETTINGS> } <INITIAL SET UP/INFORMATION> } Select "SEQUENTIAL PLAY" in the <HDD SETTINGS> screen. Select "ON" by turning the JOG, and turn the SHUTTLE ring clockwise. The setting is made, and the display stops flashing. 2. Press one of the camera number buttons with recorded video. Single screen sequential playback starts. If a power failure occurs during archive, the archive will not restart automatically after the power is restored. When the timer record setting has been preset, the archive will automatically restart after the power is restored, but from the point that the unit started archive before the power failure occurred. o ARCHIVE SOURCE HDD The ARCHIVE device can be set to archive data from the MAIN HDD, SUB HDD or LPA HDD. 50 <HDD SETTINGS> HDD REPEAT REC MAIN ON HDD REPEAT REC SUB OFF HDD REPEAT REC LPA OFF HDD REPEAT PLAY OFF IM-CHECK PLAY OFF SEQUENTIAL PLAY OFF FIFO OVERWRITE MODE OFF >>ARCHIVE SOURCE HDD MAIN ARCHIVE START POSITION RESET <ARCHIVE START POSITION RESET> >>EXECUTE 2. Turn the SHUTTLE ring clockwise. The ARCHIVE POINT is reset. Points to be careful of regarding archive This setting is appeared when "ARCHIVECOPY" is selected on "ID4ID5" of the <INITIALIZATION> screen, and the "HDD SETTING" is selected on "PARTITION" ("LONG PRE-ALARM"). Settings ( default : "MAIN" ) "MAIN" : Archive MAIN HDD only. "LPA" is appeared when "LONG PRE-ALARM" is selected on "HDD SETTING" of the <INITIALIZATION> screen after installing EXTRA HDD to "INTERNAL HDD A". 1. Press the SET UP button } <SETTINGS> } <INITIAL SET UP/INFORMATION> } Select "ARCHIVE SOURCE HDD" in the <HDD SETTINGS> screen, and display the desired setting. Press the ARCHIVE button. The ARCHIVE device commences archive. When archive is performed during record, an image may not be recorded at the time of an archive start and an end. Be careful. s AUDIO RECORDING This unit can simultaneously record audio along with the video. When recording audio, the continuous recording time becomes shorter than when recording only video. <INITIAL SET UP/INFORMATION> HDD SETTINGS >>AUDIO RECORDING OFF REAR TERMINAL SETTINGS COMMUNICATION PORT SETTINGS CAMERA CONTROL INFORMATION/SERVICE PASSWORD LANGUAGE SELECTION Setting ( default : "OFF" ) "ON" : Records video and audio. "ALARM" : During alarm recording or emergency recording, records video and audio. Press the SET UP button } <SETTINGS> } Select "AUDIO RECORDING" in the <INITIAL SET UP/INFORMATION> screen. Turn the SHUTTLE ring counterclockwise or press the SET UP button. o ARCHIVE START POSITION RESET The unit automatically keeps track of the end point of HDD archive. After reset, the ARCHIVE POINT returns to the position of the earliest stored data. <HDD SETTINGS> HDD REPEAT REC MAIN ON HDD REPEAT REC SUB OFF HDD REPEAT REC LPA OFF HDD REPEAT PLAY OFF IM-CHECK PLAY OFF SEQUENTIAL PLAY OFF FIFO OVERWRITE MODE OFF ARCHIVE SOURCE HDD MAIN >>ARCHIVE START POSITION RESET When setting "AUDIO RECORDING" to "ON", a speaker display ( ) appears to the right of recordable time display in the <RECORD SETTING> and <RECORD SETTING A> ~ <RECORD SETTING D> screens. <RECORD SETTING> 2/2 This setting is appeared when "ARCHIVECOPY" is selected on "ID4ID5" of the <INITIALIZATION> screen. Confirm that the peripheral recording device is correctly connected to ID4 or ID5, and "ARCHIVE COPY" is selected on "ID4ID5" before making ARCHIVE START POSITION RESET settings. 1. [. . . ] Kontrollera att ventilationsflkten som sitter p enhetens bakre panel inte blockeras. OLMPLIGA INSTALLATIONSPLATSER Om du placerar enheten p fljande platser kan dess livstid frkortas: Extremt kalla platser, t ex kylda magasin och fryshus. Platser dr stora mngder svavelvte bildas, t ex trakter med heta kllor. Platser eller omrden dr luften innehller saltvatten. VARNING : FR ATT UNDVIKA BRAND ELLER ELSTTAR, FR DENNA APPARAT INTE UTSTTAS FR REGN ELLER FUKT. APPARATEN MSTE JORDAS. Denna apparat uppfyller kraven angivna i EC-direktivet 89/336/EEG, "EMC Directive" och 73/23/EEG, "Low Voltage Directive", vilka ar andrade genom direktivet 93/68/EEG. [. . . ]