User manual MITSUBISHI DX-TL4516E

[. . . ] DIGITAL RECORDER USERS MANUAL MODEL DEUTSCH DX-TL4516E THIS INSTRUCTION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL RECORDER. 1 OTHERS NEDERLANDS ITALIANO ESPAÑOL FRANÇAIS ENGLISH Caution and care HEAVY OBJECTS SHOULD NEVER BE PLACED ON THE UNIT (E. G. , MONITOR) NEVER TOUCH OR INSERT ANY OBJECT INSIDE THE UNIT Touching the inside of the cabinet or inserting foreign objects of any kind through the disc loading slot or ventilation holes not only creates a safety hazard but can also cause extensive damage. PROTECT THE POWER CORD Damage to the power cord may cause fire or shock hazard. If the power cord is damaged, turn OFF the MAIN switch and carefully unplug the cord by holding the main plug. [. . . ] "Sensor" display indicates the sensor number to which the alarm signal is input. When repeat recording setting for normal and alarm areas are set to "Repeat Off" and there is an alarm recording (emergency recording) at the end of the HDD, that recording may not be stored in the alarm list and that item may be missed. When the data of the camera number which is not corresponded to the alarm sensor number is copied to the external media, the alarm list of that data is not exactly similar to that of listed in the digital recorder. When the detection of the motion or the ground of the ALARM IN terminal occurs numerously at the same time, not all the start times of the alarm recording may be registered in the alarm list. In this case, the sensor of the lowest number is registered in the list. In the alarm list, items with the ALARM IN terminal grounded are indicated in orange, items that were detected with motion are indicated in white, items with the EMERGENCY terminal grounded are indicated in magenta, and items that were input with alarm signal via communication are indicated in green. 18 Copying the recorded data ENGLISH This item is used to copy the data from the main device to a copy device. When copying the data to DVD while "Overwrite" is set to "On, " the unit clears the existing data on the disc before overwriting with new data. When copying the data while "Copy Data" is set to "Alarm, " the unit performs copy operation, however, the data is not copied if there is no alarm recording data within the specified range of copy. In case of CD/DVD disc, the remaining capacity becomes low because only the management information is recorded. It is recommended to carry out "Calculate" in <Copy Data to Copy 1 Drive> to confirm whether or not there is alarm recording data in the specified range. step3. Copy Data to Copy 1 Drive/Set Copy 1 Drive This item is used to copy the data to Copy 1 device by specifying the start and end points. This function is useful for copying the data of the short period of time. Before executing the copy, make sure that the Copy 1 device is connected and set in the <Add/Remove HDD Device> and <Add/Remove DVD/CD Drive> correctly. (System Menu Memory) User Menu 2 Copy steps 4, 5 1 Copy Data to Copy 1 Drive step 3 1 + 2 Range of Copy steps 1, 2 3 Set Copy 1 Drive step1. Set the camera number to be copied. · The button function changes between "All Off" and "All On" each time you select this button. You can switch on and off for all the cameras easily by using this button. · The picture is not copied when there is no recorded picture of the set camera number or time. Make sure to check that the picture of the specified camera has been recorded on the specified copy start point. The available setting items are "Main" and "Copy 2. " From Group: Sets the group which contains the data to be copied. The available setting items are "Normal, " "Alarm, " and "LPA" for main, "SerialBus, " "DVD/CD, " and "Internal" for copy 2. The available setting items are "SerialBus, " "DVD/CD, " and "USBmemory. " Copy Data: Sets the data area to be copied. The available setting items are "Alarm" and "All. " Overwrite: Selects whether or not to overwrite the existed data. Auto Eject: Selects whether to eject media (CD/ DVD) automatically when the copy is over. Set the start, start/end, or end point of copy by specifying the date and time or the bookmark number. [. . . ] · Restart the unit. Stop recording. LOG54 #7 Fixed It can use as it is though a slight error occurred. Output video signals. LOG43 LOG73 LOG23 #8 #8 #8 #8 #8 None System suspended due to unstable processing. Start operation again. The recorder detected the data altered or data recorded by other recorder. Internal temperature is getting too high, check the ventilation of the recorder. [. . . ]