User manual MITSUBISHI DX-TL5000EZ

[. . . ] DIGITAL RECORDER USER'S MANUAL DEUTSCH DX-TL5000E THIS INSTRUCTION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL RECORDER. 1 NEDERLANDS ITALIANO ESPAÑOL FRANÇAIS MODEL ENGLISH Caution and care HEAVY OBJECTS SHOULD NEVER BE PLACED ON THE UNIT (E. G. , MONITOR) NEVER TOUCH OR INSERT ANY OBJECT INSIDE THE UNIT Touching the inside of the cabinet or inserting foreign objects of any kind through the disc loading slot or ventilation holes not only creates a safety hazard but can also cause extensive damage. PROTECT THE POWER CORD Damage to the power cord may cause fire or shock hazard. If the mains cord is damaged, turn OFF the MAIN switch and carefully unplug the cord by holding the mains plug. [. . . ] · "Sensor" display indicates the sensor number of which the alarm signal is input. · When the repeat recording setting for "Normal Recording Area" or "Alarm Recording Area" (System Menu Memory Data Management Setting for Main Memory) is set to "Repeat Off" and there is an alarm recording (emergency recording) at the end of the HDD, that recording may not be stored in the alarm list and that item may be missed. · When the detection of the motion or the ground of the ALARM IN terminal occurs numerously at the same time, not all the start times of the alarm recording may be registered in the alarm list. In this case, the sensor of the lowest number is registered in the list. · In the alarm list, items with the ALARM IN terminal grounded are indicated in orange, items that were detected with motion are indicated in white, items with the EMERGENCY terminal grounded are indicated in magenta, and items that were input with alarm signal via communication are indicated in green. · To clear the alarm list, erase the HDD data of which the alarm recording is recorded (System Menu Data Clear). Beware that executing it erases all the data of the HDD contained the picture data. ···································································································································· Basic operations 17 ENGLISH Search by Alarm List · Alarm list search is not performed if there are no index signals. Copying the recorded data Copy (User Menu Copy) This item is used to copy the data in the main device to the copy device. · When copying the data to DVD and setting "Overwrite" to "On, " the unit clears the existed data of the disk before overwriting the data. Note that clearing the data takes about 30 to 40 minutes. step3. Copy Data to Copy A Drive/Set Copy A Drive This item is used to copy the data by specifying the start and end points of copying. This function is useful for copying the data of the short period of time. · Before executing the copy, make sure that the Copy A device is connected and set in the <Add/Remove HDD Device> and <Add/Remove DVD/CD Drive> (System Menu Memory) correctly. User Menu 2 Copy steps Set the start, start/end, or end points of the copy by specifying the date and time or the book mark. Start: Sets only the start point of the copy. · To set the point using the book mark, select "Bookmark" and then select the desired book mark number. · To copy the oldest recorded time, select "Copy Start Time. " To copy the latest recorded time, select "Copy End Time. " step4. Select "Calculate" to calculate the capacity of the data to be copied. 4, 5 1 Copy Data to Copy A Drive step 3 2 Range of Copy steps 1, 2 3 Set Copy A Drive step1. · When using "End, " the copy cannot be executed unless the calculation of the capacity of the data to be copied is completed. · When using "Start" or "Start/End" and executing the copy without calculating the capacity of the data to be copied, the progress or the time of the copy may not be displayed correctly because the unit cannot specify the capacity of the data to be copied. step5. Set the camera number to be copied. · The button function changes between "All Off" and "All On" each time you select this button. You can switch on and off for all the cameras easily by using this button. · The picture is not copied when there is no recorded picture of the set camera number or time. Select "Execute. " · The copy starts. · To stop the copy manually, select "Cancel" in the progress screen. The data which has been copied before cancelling is copied. Copy Data to Copy B Drive/Set Copy B Drive This item is used to copy the data by specifying only the start point of copying. The copy continues until the end point of the recorded data reaches or the media to be copied becomes full unless the copy is stopped manually (when "FIFO Overwrite" is set to "Off"). · Before executing the copy, make sure that the Copy B device is connected and set in the <Add/Remove HDD Device> and <Add/Remove DVD/CD Drive> (System Menu Memory) correctly. User Menu 2 Copy step step2. Select "Other settings" and then set the detailed settings. From: Sets the area which contains the data to be copied. The available setting items are "Normal, " "Alarm, " and "LPA. " To: Sets the group number to which the data is copied. The available setting items are "Group 1" to "Group 5. " Copy Data: Sets the data to be copied. [. . . ] Put a new disc into the drive. #2 : The value depends on the setting. #3 : Log number for Recording #4 : Log number for Restore #5 : Log number for COPY A #6 : Log number for COPY B Click "Clear Warning" or press the E button. (Insert the media Warning" or if there is none. ) press the E · Check whether it is write- button. · After peripheral recording device and the unit power off a power supply, reboot in the order of peripheral recording device and the unit. [. . . ]