User manual MITSUBISHI EASY02-K60

[. . . ] OPERATOR USER´S MANUAL DPS TERMINAL Model MT1 series Easyphoto v2. 4. 0 Users Manual ENGLISH Rev 1. 9 For more information please visit www. mitsubishiphoto. com and www. easyphotosystem. com. Operator users manual TABLE OF CONTENTS 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 1 The best choice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 2. 1 Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When using a PTP camera, this will detect now the connection with the easyphoto system and will change to picture source mode. NOTE Please plug the camera in the rear USB port from your MT1 system. In most of the cameras using the Mass Storage mode, they have to be manually switched to this mode at this time. 3. 7. 4 Selecting the layout Afterwards, the layout must be chosen. Split layouts (using two different colours) allow mixing two different pictures. After choosing the layout, the Photo ID screen is shown. 31/84 Operator users manual 3. 7. 5 Selecting and working with the pictures In the top area, the pictures read from the source are shown. When selecting any of them, the picture will be loaded to be shown in the central area. In this screen, its also possible to change the layout by clicking on the preview placed on the topright corner. The select layout screen will appear again to restart the workflow. 32/84 Operator users manual Once in the Photo ID screen again, its possible to select another picture. 3. 7. 6 Printing After pressing the "Print" button, a pop-up will appear in order to determine the amount of copies desired. When pressing the refresh button, the latest images from the picture source are reloaded. When using a camera with PTP connection, only the latest 8 images from the device are loaded. 33/84 Operator users manual 3. 7. 7 Automatic biometrics detection When automatic biometrics detection is active in the settings (see Administration chapter), it will take some more time and the picture could appear centred and zoomed. The easyphoto system is applying innovative imaging processing tools to detect the face of the customer and helping the operator of the system to center the picture in the biometrics mask shown in the centre of the screen. If a picture can not be correctly centred it appears a message under the picture just warning about it. The cause can be any of the following: The eyes of the customer are not clearly visible in the picture The top part of the head of the customer is too near the top egde of the picture. Depending on the print rectangle dimensions or aspect ratio, and also on the biometrics mask being used, this distance can vary. The customer brings glasses and there is a shiny spot of light over them. Some part of the face of the customer is not clearly visible The face of the customer in the picture is rotated 90º or more. The picture has poor vertical resolution (less than 500 pixel) Anyway, after automatic detection the picture can be manually adjusted. In some cases, even if there is not any error message in the screen, the face of the customer is not being centred correctly. If the current layout is not using the official ID or Passport dimensions and aspect ratio, and a biometrics mask is shown, this could be normal. The picture can be rotated in small amounts in both directions by pressing quickly the rotate button. To change the orientation of the picture (and changing the aspect ratio) to landscape or portrait, please keep pressed the rotate button for a couple of seconds. This is useful when a compatible USB camera (working as a mass storage device) is connected to the system and the photographer wants to stay working permanently in the PhotoID screen. By pressing the refresh button, the pictures are reloaded from the camera and the last picture taken is shown. Adjust the picture position to the biometric mask (when available) using the controls. For split layouts, use the group selector button at the top right of the screen before selecting the second picture to be included in current composition. Press "Finish order" each time you want to print a copy of current Photo ID composition. [. . . ] Once the process is finished correctly, the system informs about the success of the operation. If the restore total backup has not been successful, it will be notified. 6. 2. 6 Shutdown This option shuts down the system properly. Please use always this option to shut down the system after performing any of the previous options of the menu. Do not remove the USB recovery device before the equipment is switched off. 79/84 Operator users manual 7 ACTIVATING ADDITIONAL LICENSES Its required to activate additional licenses (like PhotoID) in order to access the whole functionalities of the system. [. . . ]