User manual MITSUBISHI EXTERIOR SPECIFICATIONS

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MITSUBISHI EXTERIOR. We hope that this MITSUBISHI EXTERIOR user guide will be useful to you.


MITSUBISHI EXTERIOR SPECIFICATIONS: Download the complete user guide (831 Ko)

Manual abstract: user guide MITSUBISHI EXTERIORSPECIFICATIONS

Detailed instructions for use are in the User's Guide.

[. . . ] 50 51-2 EXTERIOR - Front Bumper FRONT BUMPER SPECIAL TOOL Tool Number MB990784 Name Ornament remover Use Removal of front bumper assembly 51100060071 EXTERIOR - Front Bumper 51-3 51100140201 FRONT BUMPER REMOVAL AND INSTALLATION Pre-removal and Post-installation Operation D Splash Shield Removal and Installation (Refer to GROUP 42 - Fender. ) D Radiator Grille Removal and Installation (Refer to P. 51-12. ) <SPACE RUNNER> Section A - A 6 Pin Clip 3 4 6 5 A A 1 3 2 Removal steps 1. License plate bracket 51-4 <SPACE WAGON> Section A - A EXTERIOR - Front Bumper 6 Pin Clip 5 6 A A 5 1 2 3 4 Removal steps 1. License plate bracket Pin MB990784 REMOVAL SERVICE POINT AA" FRONT BUMPER ASSEMBLY REMOVAL 1. Remove the clip. Clip MB990784 EXTERIOR - Front Bumper DISASSEMBLY AND REASSEMBLY <SPACE RUNNER> 51-5 51100160238 5 6 B B A 2 4 A 1 C 3 C Section A - A Clip Section B - B Section C - C 6 1 Clip 4 Clip 6 Pin 2 6 Disassembly steps 1. [. . . ] Washer motor EXTERIOR - Windshield Wiper and Washer Linkage assembly 51-31 REMOVAL SERVICE POINT AA" WIPER MOTOR REMOVAL 1. Use a flat-tipped screwdriver to separate the wiper motor crank arm from the linkage assembly, and then remove the wiper motor. Caution Because the installation angle of the crank arm and the motor has been set, do not remove them unless it is necessary to do so. If they must be removed, remove them only after marking their mounting positions. Wiper motor crank arm For rear washer (Black) INSTALLATION SERVICE POINTS "AA WASHER TANK ASSEMBLY INSTALLATION When the washer tank assembly is reinstalled, make sure that the washer hoses and the control harness connectors are connected to their original positions. To rear washer For front washer (White) To front washer "BA WIPER ARM AND BLADE ASSEMBLY INSTALLATION Install the wiper blade so that the wipers stops at the specified stop position (standard value) as shown in the illustration. A A Standard value (A): <Driver's side> 45 ± 5 mm <Passenger's side> 52 ± 5 mm Front deck garnish end 51-32 EXTERIOR - Windshield Wiper and Washer INSPECTION 51100770035 51101260135 WIPER MOTOR CHECK Disconnect the wiring harness connector, and then check the wiper motor operation with the wiper motor remaining installed to the body. Wiper Motor Operation Speed Connect a battery to the wiper motor as shown in the illustration and check the operation speed. Operation speed check Stop Position 1. Connect a battery to the wiper motor as shown in the (A) of the illustration. Then run the wiper motor at low speed, disconnect the battery, and stop the motor. Connect the terminals via a jumper wire and a battery to the wiper motor as shown in the (B) of the illustration. After the motor starts turning at low speed, it should stop at the automatic stop position. High speed Low speed Stop position check (A) Low speed (B) Automatic stop 51101270015 WASHER MOTOR CHECK 1. With the washer motor installed to the washer tank, fill the washer tank with water. Check that the water squirts out strongly when battery voltage is applied to terminal (2) and terminal (1) is earthed. EXTERIOR - Windshield Wiper and Washer L. H. drive vehicles <PassenA ger's side> C D B I E H 51-33 51101270138 A F <Driver's side> WASHER FLUID EJECTION POINT CHECK Adjust the ejection angle by moving the nozzle. Item Distance mm 300 450 50 55 340 Item F G H I 250 55 325 475 A B C D E Distance mm G Ceramic end line 70 mm 50 mm Area to be ejected R. H. drive vehicles <Driver's side> F A A D <Passenger's side> C G I H E B Ceramic end line 51-34 EXTERIOR - Rear Wiper and Washer 51100880028 REAR WIPER AND WASHER SPECIAL TOOLS Tool Number MB991502 Name MUT-II sub assembly Use D D Diagnosis code check ETACS-ECU input signal check 42300060143 MB991529 Diagnosis code check harness D D Diagnosis code check ETACS-ECU input signal check by using a voltmeter TROUBLESHOOTING DIAGNOSIS FUNCTION 42300070238 INPUT SIGNAL INSPECTION PROCEDURE 1. Connect the MUT-II or a voltmeter to the diagnosis connector to check input signal. (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points. ) 2. The following input signals can be checked: D Rear wiper switch D Rear washer switch INSPECTION CHART FOR TROUBLE SYMPTOMS Trouble symptom Communication with the MUT-II is impossible. Inspection procedure 42300700083 Reference page Refer to GROUP 54 - SWS. 1 51-35 51-36 51-37 51-37 51-38 When the selector lever is moved to "R" position during the intermittent wiper 2 operation, the wiper does not operate at the continuous mode. 3 4 When the washer switch is turned on for 0. 3 seconds or more, the wiper does not 5 operate. EXTERIOR - Rear Wiper and Washer INSPECTION PROCEDURE FOR TROUBLE SYMPTOMS Inspection Procedure 1 When the wiper switch is turned on, the wiper does not operates. The cause may be a malfunction of the wiper switch input circuit, harness or connector, rear wiper motor, or ETACS-ECU. 51-35 Probable cause D D D D Malfunction Malfunction Malfunction Malfunction of of of of column switch rear wiper motor wiring harness or connector front-ECU MUT-II Self-Diag code Are any of the ETACS-ECU diagnosis codes output?NO MUT-II Input check D Rear wiper switch OK Check the rear wiper motor. (Refer to P. 51-41. ) OK Measure at the rear wiper motor connector E-03. D Ignition switch: ON D Rear wiper switch: ON D Voltage between terminal No. 2 and earth OK: System voltage OK YES INSPECTION CHART FOR DIAGNOSIS CODES (Refer to GROUP 54 - SWS. ) Check the rear wiper and washer switch input circuit system. (Refer to P. 51-38, INSPECTION PROCEDURE 6. ) NG NG Replace NG Check the following connectors: B-104, B-98, E-07, E-03 OK Check trouble symptom. [. . . ] NG Check the harness wire between the ignition switch (IG1) and the column switch, and repair if necessary. D Continuity terminal No. 4 and earth OK: Continuity OK Replace the column switch. NG Check the following connector: B-87 OK Check trouble symptom. NG Check the harness wire between the column switch and the earth, and repair if necessary. NG Repair EXTERIOR - Headlamp Washer 51-45 51100970107 HEADLAMP WASHER REMOVAL AND INSTALLATION Caution: SRS Before removal of air bag module and clock spring, refer to GROUP 52B - SRS Service Precautions and Air Bag Module and Clock Spring. 5 1 6 2 4 2 3 4 Nozzle and check valve removal steps D Draining of washer fluid D Front bumper (Refer to P. 51-3. ) 1. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MITSUBISHI EXTERIOR




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MITSUBISHI EXTERIOR will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.