User manual MITSUBISHI GB-50A FOR INITIAL SETTING WEB

[. . . ] Mitsubishi Electric Building Air-conditioner Control System Central Controller G-50A/GB-50A Operation Manual for Initial Setting Web Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-1 Conventions Used in This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-2 Computer Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-3 Notes on using G-50A with the integrated centralized control software (TG-2000A). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Setting the Operating Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2-1 Setting the PC IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Click to bring up the registration screen. Refresh Read setting data from G-50A. Save Settings Send setting data to G-50A. 4-3-1 Setting the Group Name (1) In the [Group Name for Web] field on the screen, register the group name to be displayed on the Web screen, using a name consisting of no more than 20 characters. Note: The following characters cannot be used in the group name: < > & " ' (2) Next, in the [Group name for LCD of the G-50A] field, enter the group name to be displayed on the LCD of the G-50A consisting of no more than 10 numbers, upper case letters, hyphen, or space combined. 4-3-2 Registering air conditioner units in the group (1) Clicking the [Air Conditioner Registration] field next to each group in the [Groups] screen will bring up the [Select Unit Addresses] screen. Deselected items will be shown with a gray background. Note: A maximum of 16 air conditioner units can be registered in one group. 13 (2) To register remote controllers in a group, click on the [Remote Controller Registration] field to display the [Select Unit Addresses] screen, and click on the numbers corresponding to the units to be registered. The ones that are selected will be shown with a yellow-green background. Deselected items will be shown with a gray background. Note: A maximum of 2 remote controls can be registered in one group. Note: MA remote controls do not need to be registered to a group. (3) To register system remote controllers in a group, click on the [System Controller Registration] field to display the [Select Unit Addresses] screen, and click on the numbers corresponding to the units to be registered. The ones that are selected will be shown with a yellow-green background. Deselected items will be shown with a gray background. Note: The combined number of system controllers and remote controls cannot exceed four. Note: K-transmission converters do not need to be registered. 14 4-4 Interlocked Setting To interlock the operation of LOSSNAY with the run/stop status of the indoor units, click on [Initial Settings]-[Interlocked LOSSNAY] in the menu to bring up the Interlocked LOSSNAY screen, and enter the interlock conditions. Click [Save Settings] to send setting data to the G-50A. Note: If the user logs in as a building manager, the operations may be prohibited. Note: If the system is connected to the TG-2000A, make all settings and changes from the TG-2000A so that the data in TG-2000A and G-50A will match. Interlocked LOSSNAY Registration Register the interlocked ventilation equipment here. Click to bring up the registration screen. Interlocked Indoor Units Registration Register the indoor units to which LOSSNAY units are interlocked here. Click to bring up the registration screen. Refresh Read setting data from G-50A. Save Settings Send setting data to G-50A. (1) Click in the Interlocked LOSSNAY registration field to display the [Select Unit Addresses] screen, and click on the numbers corresponding to the units to be registered. The ones that are selected will be shown with a yellow-green background. Deselected items will be shown with a gray background. (2) Click on the Interlocked Indoor Unit Registration field to display the [Select Unit Address] for the indoor units, and click on the numbers corresponding to the units to be registered. The ones that are selected will be shown with a yellow-green background. Deselected items will be shown with a gray background. Note: A maximum of 16 indoor units can be registered to operate with one ventilator. 15 4-5 Block Setting By performing block settings, multiples of air conditioner groups can be collectively monitored or operated from the Web or TG-2000A. Bring up the Block Setting screen by clicking [Initial Settings]-[Blocks] in the menu, and register the groups in the block to utilize these features. Click [Save Settings] to send setting data to the G-50A. Note: If the user logs in as a building manager, some of the operations may be prohibited. Note: If the system is connected to the TG-2000A, make all settings and changes from the TG-2000A so that the data in TG-2000A and G-50A will match. Block Name Register the block name to be displayed on the Web screen here. Group Registration Register the groups to be included in the block here. Refresh Read setting data from G-50A. Save Settings Send setting data to G-50A. 4-5-1 Registering a block name In the [Block Name] field on the screen, register the block name to be displayed on the Web screen, using a name consisting of no more than 20 characters Note: The following characters cannot be used in the group name: < > & " ` 4-5-2 Registering a group in a block Click on the Group Registration field to display [Select Groups], and click on the numbers corresponding to the groups to be registered. The ones that are selected will be shown with a yellow-green background. (Putting a cursor on the group number will display the group name. ) To cancel the selection, click on them again. Deselected items will be shown with a gray background. 16 5 Functions 1 5-1 Error mail reports/E-mail communication Click on [Functions 1] ­ [E-Mail] in the menu to open the [E-mail] window and make necessary settings to perform remote monitoring via mail, using error mail report or the maintenance tool. [. . . ] Note: The noise level to be reduced varies depending on the unit model. Note: If the user logs in as a building manager, the operations may be prohibited. Night mode start time Click to set the start time. Night mode end time Click to set the end time Target outdoor units Click to select the outdoor unit, which performs night mode control. Refresh Read setting data from G-50A. Save settings Send setting data to G-50A. (1) Set the time interval in [Night mode start time] and [Night mode end time]. Note: When the starting time and the ending time is the same, night mode operation will always be performed. (2) Select the outdoor unit, which performs night mode operation from [Target outdoor units]. Note: M-NET address numbers for each outdoor unit are displayed in the target unit field. (3) Click [Save Settings] to send setting data to the G-50A. 25 6-3 Auto-Changeover of Y series Click on [Function2]-[Auto-changeover] in the menu to open the auto-changeover screen and make necessary settings to switch the operation mode between cooling and heating automatically of the indoor units connected to the same outdoor unit. Please use this function when performing heating operation in the morning and cooling operation in the afternoon on air conditioners that either of cooling or heating operation is possible (Y series). The operation mode changes automatically without the need of operating all remote controllers. Note: The operation mode (cooling or heating) is set by the majority decision in consideration of performance value of each unit, or on the basis of the operation mode of the representative group. [. . . ]