User manual MITSUBISHI HC4000

[. . . ] DLPTM PROJECTOR MODEL HC4000 User Manual HC4000 This User Manual is important to you. Please read it before using your projector. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. If you use another power supply cord, it may cause interference with radio and television reception. Use the attached RGB cable with this equipment so as to keep interference within the limits of an FCC Class B device. [. . . ] (See page 31. ) Use this setting to make colors with medium brightness, such as yellow and the skin tone appear natural. (BrilliantColorTM has no effect at value 0. ) · For more enhanced color reproduction, set BrilliantColorTM to 0. The white area of the color wheel is disabled, and you can reproduce true-color images. For analog signal input: The input level of video signal differs among devices to be connected. High input level causes solid white in displayed image and low input level causes displayed image to get dark. For digital signal input: AUTO: The proper setting is automatically selected. (See page 16. ) When you turn COLOR MANAGEMENT on, you can change to any desired color by adjusting each of GAIN and SATURATION of six different colors. (See page 33. ) Select the AV MEMORY to which you save the current setting. (See page 30. ) ADVANCED MENU SCREEN SIZE VERTICAL LOCATION CTI INPUT LEVEL 2 options ±26 0-5 ±5 AUTO / ENHANCED / NORMAL COLOR MANAGEMENT AV MEMORY SAVE ON / OFF 3 options · · By using the AV memory function, you can save up to 3 setting patterns of IMAGE menu for each input terminal. (See page 30. ) INPUT LEVEL is unavailable when the digital signal is supplied from the YCBCR/YPBPR terminal of the connected device. EN-26 Menu operation (continued) 2. INSTALLATION menu opt. INSTALLATION KEYSTONE LAMP MODE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN BACK COLOR IMAGE REVERSE TRIGGER OUT TEST PATTERN AV MEMORY 1 0 STANDARD OFF OFF ON BLUE OFF OFF CROSS HATCH ON 2. INSTALLATION menu ITEM KEYSTONE LAMP MODE SETTING ±15 STANDARD LOW ON / OFF FUNCTION Use to correct vertical keystone distortion. The fan operating sound is reduced and the lamp lifetime becomes longer. When ON is chosen, the lamp is automatically lit when the power cord is plugged in the wall outlet. Use to set the time elapsed before the projector enters the stand-by mode when there is no signal input from the source. Use to change the color of the screen that appears when no signal is supplied. Select when viewing images from the front with the projector installed on the floor. Select when viewing images projected from the behind of the screen with the projector installed on the floor. Select when viewing images projected from the behind of the screen with the projector installed on the ceiling. Select when viewing images from the front with the projector installed on the ceiling. The trigger output signal (12 V) is output from the TRIGGER terminal when the lamp illuminates. The trigger output signal (12 V) is output from the TRIGGER terminal when the aspect ratio is set to ANAMORPHIC 1 or ANAMORPHIC 2. [. . . ] It may not display images of higher resolutions than 1920 x 1080 correctly. · If the resolution and frequency of your computer aren't shown on the table, find the compatible resolution and frequency by changing the resolution of your computer. · This projector doesn't support 480p signals from video devices having 4 lines (R, G, B, CS*) or having 5 lines (R, G, B, H, V). * : Composite Sync EN-46 Specifications (continued) Connectors SERIAL (Mini DIN 8-pin) 12 4 3 5 COMPUTER IN/COMPONENT VIDEO IN (Mini D-SUB 15-pin) 5 10 1 6 HDMI IN (HDMI 19-pin) 1 19 67 8 2 18 15 11 Spec. [. . . ]