User manual MITSUBISHI LT2-250-M1ATW PARTS CATALOG

[. . . ] Buttons, Switch, and Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connectors and Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wireless Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < Operating Range for the Remote Control > . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To avoid monitor from falling When installing the monitor using the tabletop stands (optional), take measures to prevent the monitor from falling over in case of an earthquake or other disaster to lessen the probability of injury and damage resulting from fall. As shown in the figure, secure the monitor to a solid wall or pillar using rope (commercially available) strong enough to bear the weight of the monitor. 44 kg (with the optional stands)) When you use screw hooks (commercially available), ring screw hooks, not C-shaped screw hooks (with opening), are recommended. 400 mm Screw Holes Screw hook, etc. commercially available Clamper Screw (mm) Table Handles Protective sheet 349 Caution: For preventing the monitor from falling. · Install the monitor with metal brackets for wall or ceiling installation (commercially available) on your own responsibility. For detailed procedures of installation, refer to the instructions of the metal brackets. · To lessen the probability of injury and damage resulting from fall of the monitor in case of earthquake or other disaster, be sure to consult the bracket manufacturer for installation location. · To lessen the risk of falling of the monitor, thread commercially available rope through the handles at the right and left of the monitor and secure the rope to the wall mount brackets or ceiling mount brackets. · Do not sleep where the monitor may topple over or fall in case of an earthquake or other disaster. Caution: · The effectiveness of preventing from falling substantially depends on the strength of brackets and base to which prevention device from falling is attached. When you cannot ensure sufficient strength, provide adequate reinforcement. · Though the recommended prevention from falling is intended to lessen the probability of injury and damage, it doesn't assure its effectiveness against any kind of earthquake or disaster. Select RGB 2 from the INPUT button on the LCD monitor or DVI-D button on the remote control. (See page 31) The AUDIO IN 1, 2, 3 or HDMI can be used for audio input. For connection, select AUDIO 1, 2, 3 or HDMI from the AUDIO INPUT button. You can select HDMI only when RGB 1 or 2 is selected. · · · Monitor To video output BNC x 3 DVD Player BNC-RCA adapter To audio output To audio output L R RCA BNC x 3 RCA DVI-D HDMI DVD Player DVI-D or DVI-I HDMI DVD Player To DVI-D or DVI-I output To HDMI output English-18 Connecting to a VCR / Stereo Amplifier You can connect your VCR / stereo amplifier to your LCD monitor. Refer to your VCR / stereo amplifier owner's manual for more information. Connect the LCD Monitor to a VCR / Stereo Amplifier · To connect the VIDEO IN connector (RCA, BNC or S-VIDEO) on the LCD monitor, use a video cable or S-video cable. To connect the AUDIO IN connector (RCA) on the LCD monitor, use an RCA cable. When connect the RCA or BNC connector, select VIDEO from the INPUT button on the LCD monitor or VIDEO button on the remote control. When connect the S-VIDEO connector, select VIDEO<S> from the INPUT button on the LCD monitor or VIDEO(S) button on the remote control. Turn on the LCD monitor and the amplifier only after all connections have been made. Use an RCA cable to connect the AUDIO OUT connector (RCA) on the LCD monitor and the audio input on the amplifier. For connection, select [AUDIO1], [AUDIO2], [AUDIO3] from the AUDIO INPUT button. [. . . ] Front Power Switch and computer power switch should be in the ON position. Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode. ) Check the monitor and your display card with respect to compatibility and recommended settings. If nothing is displayed on the screen when HDCP device is connected, reset the power of the device. Power Button does not respond · Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor. Image persistence · Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. [. . . ]