User manual MITSUBISHI LVP-SD10U

[. . . ] Data Projector MODEL LVP-XD10U LVP-SD10U OPERATING GUIDE Thank you very much for purchasing this DLPTM Technology Projector. Please read this operating guide to ensure a correct use of the device. After reading this manual, keep it for future reference. Outline This DLPTM Technology Projector can display various computer signals and NTSC/PAL/ SECAM video signals. Features 1. Complies with VESA DDC1/2B specifications English I COPYRIGHT Copyright © 2001 by this company. [. . . ] This may cause damage to the projector. Figure 6 Moving the projector 4 English Accessories Please check and make sure your box contains everything listed below. If any pieces are missing, contact your dealer. VENTILATION HOLE PROJECTION LENS CARRIER BA G MA AL NU REMOTE CONTROL POWER CONNECTOR (2 PIN TO 3 PIN) AAA BATTERIES QUIC K STAR T CAR D VGA CABLE (P/N. : 246D016-10) PS/2 MOUSE ADAPTER (P/N. : 246D016-20) SERIAL MOUSE ADAPTER (P/N. : 246D016-30) GENERAL CABLE (P/N. : 246D096-40) RCA CABLE (AUDIO/VIDEO) (ATTACHED TO VA-10U) (P/N. : 246D016-50) AUDIO CABLE (ATTACHED TO VA-10U) (P/N. : 246D016-60) S-VIDEO CABLE (ATTACHED TO VA-10U) (P/N. : 246D016-70) POWER CABLE (X3) (P/N. : 246D017-10) (P/N. : 246D017-20) (P/N. : 246D017-30) Figure 7 Accessories English 5 Connection A Connecting the Projector to Computer/Notebook 2 CONTROL PORT OUTPUT GENERAL CABLE (SUPPLIED) CONTROL PORT COMPUTER IN PS/2 PORT INPUT MOUSE ADAER FOR PS/2 PORT (SUPPLIED) VGA CABLE COMPUTER INPUT MPUTER OUTPUT (SUPPLIED) Figure 8 Connection to PC CONTROL PORT OUTPUT GENERAL CABLE CONTROL PORT (SUPPLIED) COMPUTER IN PS/2 PORT INPUT MOUSE ADAPTER FOR PS/2 PORT (SUPPLIED) VGA CABLE COMPUTER INPUT COMPUTER OUTPUT (SUPPLIED) Figure 9 Connection to notebook 6 English Operation Turn On/Off Procedure A Power on 3 Press the Standby/On key for 2 seconds to turn on the lamp. The LED will blink orange during the warm up and will then light solid green. "INPUT SIGNAL DETECTED, ACTIVATING AUTO IMAGE" will be displayed on the screen after the projector has identified the input signal; "SEARCHING" message will be displayed on the screen if there is no signal input; "SYNC IS OUT OF RANGE" message will be displayed on the screen if the horizontal frequency of the input signal exceeds the range of the projector. B Standby Press the Standby/On key for 2 seconds to turn off the lamp. The LED will then blink green and the lamp will shut down, but the fan will continue to run for about 1 minute to cool the lamp. After the fan stops, the LED will turn to a light solid orange. *Lamp Protection Procedure: If you try to turn on the lamp again while the LED is blinking, the projector will ignore the command until it has cooled down for one minute. External Control A Control Pad Hotkey -KEYSTONE +KEYSTONE REMOTE STANDBY/ON STANDBY/ON MENU AUTO RECEIVER INDICATOR LAMP STATUS INDICATOR Figure 10 Hotkey control pad English 7 MAIN UNIT Auto Keystone + Keystone Menu Standby/On Standby/On indicator Lamp status indicator FUNCTION To correct the size and phase of the projected image automatically. To correct the upper distortion of the projected image when keystone occurs. To correct the lower distortion of the projected image when keystone occurs. Lights or blinks when the lamp does not light. Menu operating When you press MENU button into OSD menu, all hotkeys become menu operating buttons. STANDBY/ON STANDBY/ON REMOTE RECEIVER MENU EXIT INDICATOR LAMP STATUS INDICATOR Figure 11 Menu control pad 8 English MAIN UNIT Menu (Keystone +) (Keystone -) Exit (Auto) FUNCTION To correct the upper distortion of the projected image when keystone occurs. To exit from the current page or OSD menu, and save setting changes. B Remote Control LED LASER STANDBY/ON MENU EXIT About laser beam FREEZE BLANK This remote control is class 2 (max. Beam Divergence : 3m distance about 5. 0mm x 3. 0mm (+/- 1. 5mm) L-CLICK R-CLICK MAGNIFY RETURN VOLUME MUTE BACK SIDE CAUTION : Pressing the LASER button on the provided remote control emits a laser beam. The use of controls or adjustments or procedures other than those specified herein may result in hazardous radiation exposure. Figure 12 Remote control The remote control allows you to operate the function keys on the projector and to emulate mouse function when the projector is connected to a computer. English 9 Main Unit Standby/On Freeze Magnify Disk Pad Function Turns the projection lamp on and off. (Move the picture with the Disk Pad after pressing the Magnify button. ) When the OSD menu is active, Disk Pad acts as selecting device. When the magnify function is active, use disk pad to move through the picture. And the blank screen will be revealed partially from top to bottom by pressing Blank again. The sound gets louder or quieter by pressing the "+" or "-" button. When operating in the mouse emulation mode, it registers a left mouse click. When operating in the mouse emulation mode, it registers a right mouse click. To move Left/Right among OSD items. Menu Blank Source Mute Volume Laser Mouse Left-Click Mouse RightClick Exit Drag Inserting Batteries in the Remote Control Be sure to follow instructions in placing batteries into the remote control units. Push and slide the lid in the direction of the arrow. Install two `AAA' batteries as indicated inside the battery compartment. Replace the lid and snap it into place. Caution Avoid excessive heat and humidity. Do not mix new and old or different types of batteries. 10 English Figure 13 Battery replacement process Remote Control Range The range for operation is about 10 m (about 32 feet ) when the remote control points to the projector. The distance from the screen back to the projector must be less than 10 m (about 32 feet). [. . . ] "Freeze" is released when the source button or the "Freeze" button is pressed again. There will be an OSD message as shown below: Press Mute again or the volume +/- buttons to turn off the mute. The OSD message below will appear: (The message will disappear automatically 3 seconds after the volume is adjusted. ) By pressing the magnify "+" button, the center of the picture can be magnified. Press the button again, and the image will be further magnified (to a maximum of 4X). [. . . ]