User manual MITSUBISHI LVP-X120A

[. . . ] LCD Projector User Manual X120 MODEL LVP-X120A 1 APPENDIX ESPAÑOL FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified shielded power-supply cord. If you use another cord, it may cause interference with radio and television reception. Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a Class A device. The projector automatically shuts off when the lamp is used up in about 2, 000 hours, and the projector will not turn on until lamp is replaced. DO NOT LOOK DIRECTLY INTO THE LENS WHEN PROJECTOR IS IN THE POWER ON MODE. 2 Contents Important safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Overview of the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Overview of the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Battery installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When AUTO is set, the appropriate video format is automatically selected according to the input signal. If the image does not appear correctly, select the desired video format manually. Adjust the unit to the appropriate format when the unit either is not projecting normally in auto mode or is inputting PAL-M/PAL-N signals. ( / English / Español / Deutsch / Français / Italiano / ) 18 5 SIGNAL AUTO . . . . . . . . . . . . . . . . . . Use to synchronize the projector with PC input signals so that the image is not blurred. The unit adjusts itself automatically when connected to either DVD players with a component video output terminal (Y, CB, CR or Y, PB, PR) or equipment with HDTV signal output capabilities. In cases where the unit is connected to equipment that include an RGB output terminal and which output HDTV signals, adjust the unit to RGB mode. 6 SIGNAL - USER (Normally, there is no need for adjustments. ) CLAMP POSITION/ CLAMP WIDTH . . . . . . . . . If you use a PC video card or something similar, the brighter colors of the projected image may become blurred. (Adjust to the horizontal pixels of inputting signal for normal setting. ) VERT. (Adjust to the vertical lines of inputting signal for normal setting. ) PLL . . . . . . . . . . . . . . . . . . . . . . Set to ON when displaying DVD discs which are recorded as the squeezed image (in right and left direction). 19 ENGLISH Picture adjustment Adjustment from personal computer Although this projector sets proper signal settings set automatically for the image signal from personal computers. If the images are still not projected correctly, use MENU display to adjust the projected images from personal computers. Afteradjustments are made, the new settings can be saved in user function. Select ON, and adjust BEGIN or END for image which top part is the least curved. Select FAST, NORMAL, or SLOW for image which top part is the least curved. · Do not change each menu setting in SIGNAL USER menu for normal setting. Press the $ or % button to select the memory which you wish to record (USER 1 or USER 2). Initializing the setting which has been changed Select RESET in SIGNAL menu, and press ENTER button. · When initializing, selection buttons will not work for about 2 - 18 seconds. Select AUTO in SIGNAL menu, and press the$ or % button to select the memory (USER1 or USER2). Press the$ or % button to select the memory which you wish to reset (USER 1 or USER 2). Press the$ or % button to adjust the horizontal start position (the left end). [. . . ] When having a control sequence by RS232C, reject other codes from personal computer side. * : The sending time of return command may delay depending on the condition (during changing the input signal, playing back the PC card, etc. ). · APPENDIX Control this projector by using a personal computer (Continue) [Example] Turn the power ON (' 'is for ASCII code) Sending commands from the PC etc. 30 30 21 0D '0' '0' '!' ' ' Status code from projector Meaning Command for POWER ON 30 30 21 0D '0' '0' '!' ' ' Command received (Command echo back) 4) Operation commands The operation commands execute the basic operation setting of this projector. It may not operate when changing the signal. POWER ON POWER OFF INPUT RGB INPUT VIDEO INPUT CARD ASCII !" _r1 _v1 _c1 HEX 21h 22h 5Fh 72h 5Fh 76h 5Fh 63h 31h 31h 31h · POWER OFF command will not work for 1 minute after the power is turned on. [. . . ]