User manual MITSUBISHI LVP-X390U

[. . . ] LCD Projector User Manual X400B X390 MODEL LVP-X400BU / LVP-X390U EN ­ 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET MUST BE INSTALLED NEAR THE EQUIPMENT AND SHOULD BE EASILY ACCESSIBLE. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class A device. [. . . ] (Variable LINE OUT) · If the high level of audio signal, for example DVD is supplied into COMPUTER AUDIO IN terminal, the speaker out may be distorted. EN ­ 14 Menu operation ENGLISH OFF OFF ON OFF 30 min ON IMAGE CONTRAST BRIGHTNESS COLOR MATRIX USER COLOR TEMP. SHARPNESS TINT COLOR INSTALLATION KEYSTONE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN IMAGE REVERSE MENU POSITION EXPAND MODE FRAME POSI. VIDEO SIGNAL ANAMORPHIC LANGUAGE RESET ALL MEMORY CALL HORIZ. POSITION VERT. POSITION FINE SYNC. TRACKING COMPUTER INPUT HOLD ± 30 ± 30 1 2 USER OFF STANDARD HIGH LOW USER ± 10 ± 10 ± 10 RED YELLOW GREEN CYAN BLUE MAGENTA SATURATION CONTRAST R CONTRAST B BRIGHTNESS R BRIGHTNESS B ± 30 ± 30 ± 30 ± 30 ± 30 ± 30 ±5 ± 30 ± 30 ± 30 ± 30 (Displays only when the source is selected to VIDEO) (Displays only when the source is selected to VIDEO) -15°, -12°, -9°, -6°, -3°, 0°, +3°, +6°, +9°, +12°, +15° ON , OFF OFF, 5, 10, 15, 30, 60 min ON , OFF OFF, MIRROR, INVERT, MIRROR INVERT 1 (Upper left), 2(Lower right) 1-4 (AUTO : When the source is selected to COMPUTER) 1-5 AUTO , NTSC , PAL , SECAM , 4. 43NTSC , PAL-M , PAL-N , PAL-60 ON , OFF , English , Español , Deutsch , Français , Italiano , OK AUTO, USER1, USER2 0 - 999 * 0 - 999 * 0 - 39 0 - 9999 * RGB, YCBCR / YPBPR AUTO ON OFF FEATURE SIGNAL * : Setting range is different according to the type of the signal. BEGIN END -1 - -99 1 - 99 0 - +63 * 1 - 63 * 0 - 9999 * 0 - 9999 * AUTO, 0 - 7 AUTO, ON, OFF 0 - 383 0 - 383 0 - 510 0 - 510 USER MEMORIZE DELETE DEFAULT USER1, USER2 USER1, USER2 CLAMP POSITION CLAMP WIDTH HORIZ. SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) Basic operation Several settings can be adjusted using Menu. Press the { or } button to select AUTO POWER OFF. AUTO POWER ON AUTO POWER OFF ON SPLASH SCREEN Opt XGA60 IMAGE 2. Press the $ or % button to adjust auto power off time. AUTO POWER ON AUTO POWER OFF ON XGA60 SPLASH SCREEN INSTALLATION 3. · If the menu operation is not working, press the RESET button on the terminal board using a suitable sharp object, push gently. · The settings with 2 mark, you should press the ENTER button after selecting. XGA60 0° OFF OFF ON OFF INSTALLATION KEYSTONE AUTO POWER ON AUTO POWER OFF ON SPLASH SCREEN IMAGE REVERSE EN ­ 15 Menu operation (continued) 1 IMAGE CONTRAST . . . . . . . . The color balance of the image shifts green as the number increases and shifts to purple as the number decreases (displays only when the source is selected to VIDEO). · When the TV50 (PAL, SECAM) signal is inputted, you cannot adjust the TINT. Adjusts the color intensity of the image (displays only when the source is selected to VIDEO). Opt 2 INSTALLATION KEYSTONE . . . . . . . . If the image has XGA60 keystone distortion, select the approximate setting. To select whether to boot up automatically when the power is 0° KEYSTONE turned on external to the projector. In this case, the main AUTO POWER OFF ON power switch of the projector has to be ON. Set this when the AUTO POWER OFF OFF projector is hanging on the ceiling. SPLASH SCREEN ON · The projector is in stand-by mode when the lamp is not IMAGE REVERSE OFF on. Use to select the length of time before projector switches to stand-by when there is no input signal selected source. Use to display the splash screen on the screen when the power is turned ON. MIRROR, INVERT is for rear projection ceiling mount. Opt ON 3 FEATURE MENU POSITION . Use to select the position where the menu is displayed, (upper left) or (lower right). VIDEO SIGNAL image does not appear correctly, select the desired video ANAMORPHIC format manually. Set ON when displaying DVD discs which are recorded in RESET ALL letter boxed images. [. . . ] (3) The personal computer checks the command and confirms if the command which has been sent has been executed or not. When having a control sequence by RS232C, reject other codes from personal computer side. · * : The sending time of return command maybe delayed depending on the condition (during changing the input signal, etc. ). [Example] Turn the power ON (' 'is for ASCII code) Sending commands from the PC etc. 30 30 21 0D '0' '0' '!' ' ' Status code from projector Meaning Command for POWER ON 30 30 21 0D '0' '0' '!' ' ' Command received (Command echo back) 4) Operation commands The operation commands execute the basic operation setting of this projector. [. . . ]