User manual MITSUBISHI LVP-X400U

[. . . ] LCD Projector User Manual X400 MODEL LVP-X400U EN ­ 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET MUST BE INSTALLED NEAR THE EQUIPMENT AND SHOULD BE EASILY ACCESSIBLE. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class A device. [. . . ] AUTO POSITION button When the source is selected to COMPUTER and the image is not in the right place, set the screen to the brightest display possible, then press the AUTO POSITION button on the remote control. · Set screen to the brightest display as possible (e. g. , full-screen display of the "Trash" window) before deploying the automatic adjustment function. · If the screen saver is running, turn off the screen saver before using the automatic adjustment button. The volume from the speaker Press the volume + or ­ button to change the volume from the speaker. The volume control bar will appear on the screen. AUDIO 15 AV mute Image and audio are temporarily muted by pressing the MUTE button. To restore the image and audio to the normal mode, press the MUTE button again. · To prevent the damage of the LCD, the image and audio will be restored automatically to the normal mode, 10 minutes after setting the AV mute mode. · The audio from the AUDIO OUT jack is also muted by pressing the MUTE button. Caution: · When you have finished using this equipment, wait 120 seconds for the exhaust fans to stop. Then turn off the main switch and unplug the power cable from the wall outlet, for safety purposes. · After the lamp is turned off, the lamp cannot be switched on again for 60 seconds as a precautionary measure. If you wish to turn on the projector again, wait until the indicator is off then press the POWER button. · The exhaust fan rotates faster when the temperature around the projector rises. · When the temperature around the projector becomes too high, the sign "TEMP!!" blinks red on the screen. If the temperature stays too high, the lamp will be shut off automatically . The projector automatically shuts off when the lamp is used up in about 1, 500 hours and cannot be used until the lamp is replaced and the internal timer is reset. See page 23. · The volume control bar will disappear about 10 seconds after releasing the volume buttons. · The volume buttons do not work when MENU selection bar or MENU is displayed. · The volume from the AUDIO OUT jack is also changed by pressing the volume + or ­ button. (Variable LINE OUT) · If the high level of audio signal, for example DVD is supplied into COMPUTER AUDIO IN terminal, the speaker out may be distorted. EN ­ 14 Menu operation ENGLISH OFF OFF ON OFF 30 min ON PICTURE CONTRAST BRIGHTNESS COLOR MATRIX USER COLOR TEMP. SHARPNESS TINT COLOR INSTALLATION KEYSTONE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN IMAGE REVERSE MENU POSITION EXPAND MODE FRAME POSI. VIDEO SIGNAL ANAMORPHIC LANGUAGE RESET ALL MEMORY CALL HORIZ. POSITION VERT. POSITION FINE SYNC. TRACKING COMPUTER INPUT HOLD ± 30 ± 30 1 2 USER OFF STANDARD HIGH LOW USER ± 10 ± 10 ± 10 RED YELLOW GREEN CYAN BLUE MAGENTA SATURATION CONTRAST R CONTRAST B BRIGHTNESS R BRIGHTNESS B ± 30 ± 30 ± 30 ± 30 ± 30 ± 30 ±5 ± 30 ± 30 ± 30 ± 30 (Displays only when the source is selected to VIDEO) (Displays only when the source is selected to VIDEO) -15°, -12°, -9°, -6°, -3°, 0°, +3°, +6°, +9°, +12°, +15° ON , OFF OFF, 5, 10, 15, 30, 60 min ON , OFF OFF, MIRROR, INVERT, MIRROR INVERT 1 (Upper left), 2(Lower right) 1-4 (AUTO : When the source is selected to COMPUTER) 1-5 AUTO , NTSC , PAL , SECAM , 4. 43NTSC , PAL-M , PAL-N , PAL-60 ON , OFF , English , Español , Deutsch , Français , Italiano , OK AUTO, USER1, USER2 0 - 999 * 0 - 999 * 0 - 39 0 - 9999 * RGB, YCBCR / YPBPR AUTO ON OFF OPTION SIGNAL * : Setting range is different according to the type of the signal. BEGIN END -1 - -99 1 - 99 0 - +63 * 1 - 63 * 0 - 9999 * 0 - 9999 * AUTO, 0 - 7 AUTO, ON, OFF 0 - 383 0 - 383 0 - 510 0 - 510 USER MEMORIZE DELETE DEFAULT USER1, USER2 USER1, USER2 CLAMP POSITION CLAMP WIDTH HORIZ. [. . . ] The projector is not at a right angle to the screen. Reduce screen size to within 40" to 300". Adjust brightness, contrast. Adjust the angle of the projector to make a right angle to the screen. When you see the stationary image for a long time, it may remain on the screen if you change the The image remains · image. Red, blue or green dots are · It is normal. viewed on the text of image. The image is distorted on the screen and noise is heard. [. . . ]