User manual MITSUBISHI LVP-X80U

[. . . ] LCD Projector User Manual X80 MODEL LVP-X80U EN ­ 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class A device. [. . . ] Then turn off the main switch and unplug the power cable from the wall outlet, for safety purposes. · After the lamp is turned off, the lamp cannot be switched on again for 60 seconds as a precautionary measure. If you wish to turn on the projector again, wait until the indicator is off then press the POWER button. · The exhaust fan rotates faster when the temperature around the projector rises. · When the temperature around the projector becomes too high, the sign "TEMP!!" blinks red on the screen. If the temperature stays too high, the lamp will be shut off automatically . The projector automatically shuts off when the lamp is used up in about 2, 000 hours and cannot be used until the lamp is replaced and the internal timer is reset. See page 23. EN ­ 14 Menu operation ENGLISH OFF OFF OFF 30 min IMAGE CONTRAST BRIGHTNESS COLOR MATRIX USER COLOR TEMP. ± 30 ± 30 sRGB STANDARD USER STANDARD HIGH LOW USER ± 10 ± 10 ± 10 RED YELLOW GREEN CYAN BLUE MAGENTA SATURATION CONTRAST R CONTRAST B BRIGHTNESS R BRIGHTNESS B ± 30 ± 30 ± 30 ± 30 ± 30 ± 30 ±5 ± 30 ± 30 ± 30 ± 30 SHARPNESS TINT COLOR INSTALLATION KEYSTONE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN IMAGE REVERSE MENU POSITION EXPAND MODE FRAME POSITION AUDIO MODE VIDEO SIGNAL ANAMORPHIC LANGUAGE RESET ALL MEMORY CALL HORIZ. POSITION VERT. POSITION FINE SYNC. TRACKING COMPUTER INPUT HOLD (Displays only when the source is selected to VIDEO) (Displays only when the source is selected to VIDEO) -15°, -12°, -9°, -6°, -3°, 0°, +3°, +6°, +9°, +12°, +15° ON, OFF OFF, 5, 10, 15, 30, 60 min ON, OFF OFF, MIRROR, INVERT, MIRROR INVERT 1=Upper left, 2=Lower right 1-4 (AUTO : When the source is selected to COMPUTER) 1-5 COMPUTER, VIDEO, C/V AUTO, NTSC, PAL, SECAM, 4. 43NTSC, PAL-M, PAL-N, PAL-60 ON, OFF , English, Español, Deutsch, Français, Italiano, OK AUTO, USER1, USER2 0 - 999 * 0 - 999 * 0 - 39 0 - 9999 * RGB, YCBCR / YPBPR AUTO ON OFF FEATURE SIGNAL * : Setting range is different according to the type of the signal. BEGIN END -1 - -99 1 - 99 0 - +63 * 1 - 63 * 0 - 9999 * 0 - 9999 * AUTO, 0 - 7 AUTO, ON, OFF 0 - 383 0 - 383 0 - 510 0 - 510 USER MEMORIZE DELETE DEFAULT USER1, USER2 USER1, USER2 CLAMP POSITION CLAMP WIDTH HORIZ. SYNC SHUTTER (U) SHUTTER (L) SHUTTER(LS) SHUTTER(RS) Basic operation Several settings can be adjusted using Menu. Press the { or } button to select AUTO POWER OFF. AUTO POWER ON AUTO POWER OFF 5. Press the $ or % button to adjust auto power off time. AUTO POWER ON AUTO POWER OFF XGA60 IMAGE 2. · If the menu operation is not working, press the RESET button on the terminal board using a suitable sharp object, push gently. · The settings with 2 mark, you should press the ENTER button after selecting. XGA60 INSTALLATION 3. Press the ENTER button (or } button). Opt XGA60 0° OFF OFF ON OFF INSTALLATION KEYSTONE AUTO POWER ON AUTO POWER OFF ON SPLASH SCREEN IMAGE REVERSE EN ­ 15 Menu operation (continued) 1 IMAGE CONTRAST . . . . . . . . The color balance of the image shifts green as the number increases and shifts to purple as the number decreases (displays only when the source is selected to VIDEO). · When the TV50 (PAL, SECAM) signal is inputted, you cannot adjust the TINT. Adjusts the color intensity of the image (displays only when the source is selected to VIDEO). Opt 2 INSTALLATION KEYSTONE . . . . . . . . If the image has XGA60 keystone distortion, select the approximate setting. To select whether to boot up automatically when the power is AUTO POWER OFF ON turned on external to the projector. In this case, the main AUTO POWER OFF OFF power switch of the projector has to be ON. Set this when the SPLASH SCREEN ON projector is hanging on the ceiling. [. . . ] Adjust the angle of the projector to make a right angle to the screen. When you see the stationary image for a long time, it may remain on the screen if you change the The image remains · image. Red, blue or green dots are · It is normal. viewed on the text of image. The image is distorted on the screen and noise is heard. Adjustments cannot be made. · The cable for connection with other equipment is not plugged securely into the terminal. [. . . ]