User manual MITSUBISHI MA-EF503HS-U REV00-11

[. . . ] q When replacing, always replace batteries at the same time using the same type. q If the electrolyte from the alkaline batteries comes into contact with skin, wash thoroughly with water. If the electrolyte accidentally enters your eye, flush with water and seek immediate medical attention. Injury and/or malfunction may occur if mishandled. 3 Precautions This air purifier is for household use only. [. . . ] The infrared rays of the sunlight may effect the remote sensor on the unit In rooms with inverter lighting for lower power consumption. The noise from the inverter lighting may effect the remote sensor on the unit. Viewing the monitor lamps The lamps light up (four levels) depending on amount of air contaminants or odors present. FAN SPEED MAX MIN Clean air Dirty air 9 Changing the airflow You can select between FAN (manual) and AUTO operation modes. On the main unit You can select from 5 airflow volumes or AUTO. Using the remote controller You can select the airflow volume from the remote controller. The operation is the same as with the main unit. HOUR MIN LOW MED HIGH MAX POLLEN GUARD NORMAL POWER TIMER FAN AUTO ON/OFF POWER AUTO FAN FAN AUTO PLASMA TIMER AUTO FAN Press one of the buttons Press one of the buttons q FAN You can select from 5 airflow volumes. The airflow changes each time the button is pressed, and the lamp of the chosen volume lights up. beep beep s MIN or LOW When sleeping s HIGH or MAX When house cleaning MIN LOW MED HIGH MAX q q AUTO You can select from POLLEN GUARD and NORMAL. Operation switches every time the button is pressed, and the selected operation mode lamp lights. Operation is automatically adjusted to the appropriate airflow volume according to the odor monitor, microdust monitor, and pollen monitor. beep POLLEN GUARD NORMAL s POLLEN GUARD q q The sensor is set to supersensitive to react to even the slightest traces of pollen. The fan speed is faster than the NORMAL operation for easier intake of large particles such as pollen, etc. The level of air pollution in the room is monitored using the odor and dust sensors, and the appropriate airflow volume is automatically selected. When the air is clean, the fan will stop. s NORMAL q q q The unit will return to the previously set mode even after turning the unit off. The unit will return to the previously set mode even when reinserting the power plug or after having a power failure. 10 Plasma air deodorization The unit uses the odor sensor to monitor the level of air pollution, then automatically activates the Plasma to break up odor ingredients in the air. Using the remote controller You can turn the Plasma deodorization function ON or OFF. ON POWER OFF beeep q beep FAN AUTO PLASMA TIMER PLASMA q Press q q q Since the unit operates intermittently during the Plasma deodorization, a hissing noise may be heard, and the unit may also stop at times. If the noise becomes irritating, turn off the feature by pressing the PLASMA button on the remote control. When the Plasma deodorization lamp is blinking, turn the unit off, and clean the Plasma unit. 13 Each time you press this button, the Plasma unit turns ON or OFF. The unit will return to the previously set operation mode when power is interrupted. To operate from the main unit, you can turn the Plasma deodorization ON or OFF using the following procedure: q When the power is turned on, press and hold the AUTO button, and press the POWER switch. Changing the airflow How to Use Plasma air deodorization/Off timer operation Off TIMER operation On the main unit You can set the unit so that it turns off after running for a preset time. (1, 2, 4 hours) Using the remote controller You can also use the remote controller to set/deactivate the off TIMER. The operation is the same as on the main unit. HOUR MIN LOW MED HIGH MAX POLLEN GUARD NORMAL POWER TIMER FAN AUTO ON/OFF POWER TIMER AUTO FAN Press q PLASMA TIMER The remaining operation time can be changed. TIMER Press beeep Continuous Operation (Lamp off) q q beep beep beep HOUR The selected Off TIMER lamp lights. The Off TIMER lamp will display the remaining operation time and will switch as time passes. 11 WARNING Maintenance Before cleaning the unit, turn off the power and remove the power plug. Electrical shock and/or injury may occur as a result. Monthly Yearly Cleaning Sensors, the HEPA filter, and main unit Cleaning the Plasma unit Replacing the filters 14 Monthly cleaning For the best performance from your unit, clean approximately once a month. Cleaning the sensors Odor sensor (control panel) Remove dust using the nozzle of a vacuum cleaner. Cleaning the HEPA filter 1 Press the grill release buttons on each side, and remove the intake grill. Both sides 2 Remove surrounding dust using the nozzle brush of a vacuum cleaner. Remove the HEPA filter and clean. Using the soft nozzle brush of a vacuum cleaner, Dust sensor surroundings Cleaning the main unit Intake grill Remove dust using a nozzle brush of a vacuum cleaner. remove dust by taking care not to tear the HEPA filter surface. Do not wash. The filter cannot be reused if washed or after becoming wet. 3 Replace the HEPA filter. 8 of ion ectirflow Dir a For stubborn dirt, remove the intake grill, and wash with a soft sponge. Thoroughly dry before replacing. Main unit Dry-wipe with a soft cloth. For stubborn dirt, wipe with a cloth dampened with water. 4 Replace the HEPA filter with the logo facing you and arrows pointing away from you. Replace the intake grill. Hook the five tabs on the upper side of the intake grill, and press in the lower side until the release buttons snap securely. 12 WARNING Before cleaning the unit, turn off the power and remove the power plug. [. . . ] Have the batteries been completely depleted or are the and of the batteries set correctly? 14 12~13 Fan noise and vibration are louder than before 14 One of the following lamps flash: FAN/POLLEN GUARD/NORMAL Plasma deodorization lamp flashes The remote controller does not work 8 13 8 Replacing the filters Maintenance q The following symptoms are not malfunctions. Symptom The air fan does not turn, or there is no air discharge A small hissing noise is heard, or there is a smell of ozone during the Plasma deodorization The monitors do not change much (Odor monitor, microdust monitor and pollen monitor) Cause Is the unit operating in AUTO (NORMAL) mode?During the Plasma deodorization, you may hear a small hissing noise or notice an ozone smell. (The level of noise and degree of the smell of ozone will vary depending on the environment. The generated ozone is of low concentration and is harmless to the body. ) Is the room too large? [. . . ]