User manual MITSUBISHI P93DW

[. . . ] DIGITAL MONOCHROME PRINTER MODEL P93DW P93DE OPERATION MANUAL BRT CONT LOCK BRT/CONT DOWN UP LOCK FEED COPY OPEN THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL MONOCHROME PRINTER. DIGITAL MONOCHROME PRINTER This digital monochrome printer complies with the requirements of the EC Directive 89/ 336/EEC, 73/23/EEC, 93/42/EEC and 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on smallscale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system. FOR THE MODEL P91DW(UB) ONLY WARNING: In the USA or Canada, use the AC power cord according to the recommendations as below, in order to comply with UL2601-1 and CAN/CSA C22. 2 No. [. . . ] Store the printed paper in a place with low humidity free from a direct sunlight. If the paper absorbs non-volatile organic solvents (alcohol, ester, katone, etc. ) the print may be discolored. Particularly, if the paper comes in contact with soft vinyl chloride such as a transparent tape, it quickens discoloration. Immediately after the paper is replaced, 2-3 images may be printed with a blank part due to hand's dust or oil. Avoid direct sunlight or places near heaters, etc. , and store the paper in a place with 30°C ( 86°F) or lower temperature and 35-80% RH. 2 2 When the paper is rapidly transferred from a cool place to a hot place, a vapor or a dew is generated on the paper surface causing paper jam or degraded printing quality. A finger print or dust on the paper surface may degrade the printing quality. Note: Mitsubishi brand thermal paper is specially treated with an anti-static coating against thermal head damage caused by static-electricity discharge. The use of non-treated paper may cause premature head failure in your product. 3 SAFETY TECHNICAL CHECKS Periods: According to the recommendations of the manufacturer of medical device. Scope: a) Visual check Housing, cables, operator controls, readout device ( displays, LED etc. ), labels, accessories, instruction manual. instruction manual, also unity and applicability of set and accessory test. c) Electrical check Safety electrical test of the configuration in accordance with EN60601-1. " In the interest of safety, avoid the handling of liquids beside the set. " RESPONSIBILITY OF THE MANUFACTURER The manufacturer, assembler, installer or importer considers himself responsible for the effects on safety, reliability and performance of the EQUIPMENT only if: ­ assembly operations, extensions, re-adjustments, modifications or repairs are carried out by persons authorized by him, and ­ the electrical installation of the relevant room complies with the IEC requirements ­ the EQUIPMENT is used in accordance with the instructions for use. · Any service after expiration of the warranty period will be chargeable. Consult your dealer for advice. TECHNICAL DESCRIPTION The supplier will make available on request such circuit diagrams, component part lists, descriptions, calibration instructions or other information which will assist the USER's appropriately qualified technical personnel to repair those parts of the EQUIPMENT which are classified by the manufacturer as repairable. The use of ACCESSORY equipment not complying with the equivalent safety requirements of this equipment may lead to a reduced level of safety of the resulting system. Consideration relating to the choice shall include: ­ use of the accessory in the PATIENT VICINITY ­ evidence that the safety certification of the ACCESSORY has been performed in accordance to the appropriate EN60601-1 and/or EN60601-1-1 harmonized national standard. The transportation and storage environmental conditions are: Temperature : -20°C - +60°C (-4°F - +140°F) Humidity : 90%RH or less at 40°C (104°F) Note : The above transportation environmental conditions indicate the storage environmental conditions during transport. 4 3 UNPACKING 3 Take the unit out of the box carefully. · Make sure to keep the unit horizontal. Take the unit out of the box by the following procedures. Make sure to check the contents. 1 Open the top of the box. 2 Remove the cushion above the unit. 4 Unwrap the unit. Accessories Thermal paper AC power cord Cleaning paper Operation manual Printer driver (1 CD-ROM) 5 4 FEATURES AND FUNCTIONS Front Panel 1 2 3 4 5678 9 BRT CONT LOCK BRT/CONT DOWN UP LOCK FEED COPY A B OPEN 1 2 3 4 5 6 7 8 9 A B Name Power switch Indicator Function Turns on/off the power. Reference Page 11 · 20 11·14·16-19 10·13 13 14 14 15 12 11 8·11·20 8·20 Displays stand-by, functions and error messages. Indicator (BRT/CONT/LOCK) Displays the settings of brightness, contrast and button function lock BRT(brightness)/ Makes fine adjustments of the brightness and contrast of the print image. CONT(contrast) button DOWN button UP button LOCK button FEED button COPY button Print exit/Cutter Lever Press to decrease the setting value. Printed paper will come out through this slot. / Cut the printed paper here. Switch to open the door. 6 Rear Panel C 1234 ON OFF D USB AC LINE 1 LOCK ON OFF 2 3 4 DIP SW DIP SW FUNCTION TABLE NO. [. . . ] Roll the cleaning paper and install into the set. Keep pressing the FEED button until you hear a beep. 6 Take out the cleaning paper. OPEN Open the door. Do not pull out the Cleaning paper Red mark Adjust the red mark on the cleaning paper parallel to the platen roller. Cleaning paper cleaning paper while the door is closed. 7 Repeat the steps 3-6 by 2 or 3 times, 6 and print 1-2 sheets to verify the cleaning effect. Platen roller CAUTION 0 It is recommended that after printing 10 rolls of paper the unit be cleaned using the supplied cleaning paper. 0 If the symptom of the dirty head is not corrected even after cleaning, your set needs repairing, contact your dealer. [. . . ]