User manual MITSUBISHI P93W

[. . . ] VIDEO COPY PROCESSOR MODEL P93W P93E OPERATION MANUAL SIDE NOR 1:1 BRT CONT EXP. SIZE MULTI SINGLE EXP. ADJUST BRT CONT FUNC FEED COPY PRINT MODE OPEN THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR VIDEO COPY PROCESSOR. VIDEO COPY PROCESSOR This video copy processor complies with the requirements of the EC Directive 89/336/ EEC, 73/23/EEC, 93/42/EEC and 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on smallscale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system. FOR THE MODEL P91DW(UB) ONLY WARNING: In the USA or Canada, use the AC power cord according to the recommendations as below, in order to comply with UL2601-1 and CAN/CSA C22. 2 No. [. . . ] · Do not touch the cutter blade. 9 6 EXAMPLE OF CONNECTION / SETTING OF SWITCHES Connecting to various composite video signal equipment such as medical equipment. Composite Video Signal Video signal equipment Television 1 Turn off the power switches of the Video copy processor and the equipment to be connected. 2 Connect the VIDEO input terminal of the Video copy processor to the video output terminal of the connected equipment. To VIDEO output terminal To VIDEO IN terminal Rear panel REMOTE ON OFF DIP SW IN VCR To VIDEO OUT terminal Video disc player To VIDEO input terminal OUT VIDEO 4 5 RESERVED 6 AC LINE DIP SW FUNCTION TABLE NO. FUNCTION SW-ON SW-OFF 1 IMP 75 HIGH 2 TRAP ON OFF 3 MEMORY FIELD FRAME Connect Power cord Camera-type VCR Monitor Setting of Switches 2 2 The following is an example of DIP switch setting. 1 2 3 4 5 6 Setting 75 ON FRAME OFF OFF OFF ON OFF DIP SW 10 Medical Video Signal 1 Turn off the power switches of the Video copy processor and the equipment to be connected. 2 Connect the VIDEO input terminal of the Video copy processor to the video output terminal of the connected equipment. Rear panel To VIDEO IN terminal ON OFF To VIDEO output terminal REMOTE DIP SW IN OUT VIDEO 4 5 RESERVED 6 AC LINE DIP SW FUNCTION TABLE NO. FUNCTION SW-ON SW-OFF 1 IMP 75 HIGH 2 TRAP ON OFF 3 MEMORY FIELD FRAME Medical equipment Connect Power cord Setting of Switches Set the DIP switch as follows: (This is standard setting. ) ON OFF SW-NO. 1 2 3 4 5 6 Setting 75 OFF FRAME OFF OFF OFF DIP SW DIP SW FUNCTION TABLE NO. FUNCTION SW-ON SW-OFF 1 IMP 75 HIGH 2 TRAP ON OFF 3 MEMORY FIELD FRAME 4 5 RESERVED 6 2 Select -curve " " - " " for ultrasonic diagnosis equipment. Refer to the " DIP SWITCH FUNCTIONS " on page 29 . 11 2 7 PRINTING 3 Cut the printed paper. · Press the "POWER" switch to turn on the power. · Cut the printed paper with the cutter by tearing off the paper in the upper right direction. cutter Printing Procedure 1 Turn on the power. 2 Print a picture displayed on the screen. · Display a picture to be printed on the monitor screen, and press the PRINT button. When printing finishes, a buzzer tone will be heard. Copy Printing 2 You can set the number of copies by pressing the COPY button on the front panel. You can copy the same picture as many times as you desire by pressing the COPY button. When pressing the FEED button during copy printing, the copy printing is canceled upon completion of the current copy. FEED COPY Paper Feeding 2 To feed the paper, hold down the FEED button on the front panel. 12 Use of Remote Control Connect the wired remote control to the remote control terminal on the rear panel. When no signal is input, the button is invalid. Rear panel ON OFF REMOTE DIP SW IN OUT VIDEO 4 5 RESERVED 6 AC LINE DIP SW FUNCTION TABLE NO. FUNCTION SW-ON SW-OFF 1 IMP 75 HIGH 2 TRAP ON OFF 3 MEMORY FIELD FRAME To remote control terminal Precautions on Printing When dark pictures are printed consecutively, the Video Copy Processor may become overheated and the indicator blinks. Avoid pulling out or holding the paper during printing or copying to prevent paper jam. When printing is carried out with no signal input, "NO SIGNAL" will be printed at the bottom of the print. Paper saving mode When the paper saving mode (SAVING : ) is selected to " " by FUNC button, the amount of paper fed is smaller than in normal paper feeding. Press and hold the FEED button on the front panel to feed the paper to cut the paper at the appropriate position. 13 8 ADJUSTMENT OF PRINT PICTURE Adjustment of Brightness/Contrast You can adjust brightness and contrast of the printed picture while observing the monitor screen. Control panel SIDE NOR 1:1 BRT CONT EXP. SIZE MULTI SINGLE EXP. ADJUST BRT CONT FUNC FEED COPY MODE · For adjustment, use the BRT button " BRT ", CONT button " CONT " and ADJUST control " ADJUST ". 1 Press the buttons to adjust brightness or contrast. BRT SIDE NOR 1:1 BRT CONT EXP. SIZE MULTI SINGLE EXP. ADJUST BRT CONT FUNC FEED COPY PRINT MODE Press the BRT button " the brightness. " to adjust · The BRT indicator lights up. OPEN CONT SIDE NOR 1:1 BRT CONT EXP. SIZE MULTI SINGLE EXP. ADJUST BRT CONT FUNC FEED COPY PRINT MODE OPEN Press the CONT button " " to adjust the contrast. · The CONT indicator lights up. 14 2 Change the setting. ADJUST 3 Store the set value. By pressing the PRINT button, the setting value is memorized. The memorized value will not be lost even when the power is turned off. · Turn the control clockwise to increase the value. ADJUST · Turn the control counterclockwise to decrease the value. The setting value is displayed by the indicator. [. . . ] In this case, clean the thermal head by the following procedure BY USING THE SUPPLIED CLEANING PAPER. Close the door without taking out the cleaning paper. 2 Open the door. Switch the left side lever to the OPEN position. OPEN 5 Press the "FEED" button. FEED 3 Insert the cleaning paper. Roll the cleaning paper and install into the set. Keep pressing the FEED button until you hear a beep. 6 Take out the cleaning paper. OPEN Open the door. [. . . ]