User manual MITSUBISHI P95DW

[. . . ] DIGITAL MONOCHROME PRINTER MODEL P95DW P95DE OPERATION MANUAL THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL MONOCHROME PRINTER. DIGITAL MONOCHROME PRINTER This digital monochrome printer complies with the requirements of the EC Directive 93/42/EEC. FOR THE MODEL P91DW(UB) ONLY WARNING: In the USA or Canada, use the AC power cord according to the recommendations as below, in order to comply with UL60601-1 and CAN/CSA C22. 2 No. The AC power cord should be UL or CSA approved and consist of type SJT, size 16 or 18AWG, length 2. 5m or shorter cord with IEC60320-1/C13 type, 125V 10A or higher rating connector and NEMA 5-15 type, 125V 10A or higher rating, Hospital Grade plug. The AC power cord should be UL or CSA approved and consist of type SJT, size 16 or 18AWG, length 2. 5m or shorter cord with IEC60320-1/C13 type, 250V 10A or higher rating connector and NEMA 6-15 type, 250V 10A or higher rating, Hospital Grade plug. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] When the remaining length of the paper is about 10" (25cm), a color belt appears at the paper end. If the remaining paper length is less than 10" (25cm), printing becomes uneven due to the uneven paper core surface. When the Printed paper is touched by wet hand, the print may be discolored. When the paper runs out during printing, the printing operation stops and "EP" is displayed by the indicator on the front panel. Store the printed paper in a place with low humidity free from a direct sunlight. If the paper absorbs non-volatile organic solvents (alcohol, ester, katone, etc. ) the print may be discolored. Particularly, if the paper comes in contact with soft vinyl chloride such as a transparent tape, it quickens discoloration. Immediately after the paper is replaced, 2-3 images may be printed with a blank part due to hand's dust or oil. Avoid direct sunlight or places near heaters, etc. , and store the paper in a place with 30°C (86°F) or lower temperature and 35-80% RH. When the paper is rapidly transferred from a cool place to a hot place, a vapor or a dew is generated on the paper surface causing paper jam or degraded printing quality. A finger print or dust on the paper surface may degrade the printing quality. Note: Mitsubishi brand thermal paper is specially treated with an anti-static coating against thermal head damage caused by static-electricity discharge. The use of non-treated paper may cause premature head failure in your product. 3 SAFETY TECHNICAL CHECKS Periods: According to the recommendations of the manufacturer of medical device. Scope: a) Visual check Housing, cables, operator controls, readout device (displays, LED etc. ), labels, accessories, instruction manual. instruction manual, also unity and applicability of set and accessory test. c) Electrical check Safety electrical test of the configuration in accordance with EN60601-1. " In the interest of safety, avoid the handling of liquids beside the set. " RESPONSIBILITY OF THE MANUFACTURER The manufacturer, assembler, installer or importer considers himself responsible for the effects on safety, reliability and performance of the EQUIPMENT only if: ­ assembly operations, extensions, re-adjustments, modifications or repairs are carried out by persons authorized by him, and ­ the electrical installation of the relevant room complies with the IEC requirements ­ the EQUIPMENT is used in accordance with the instructions for use. · Any service after expiration of the warranty period will be chargeable. Consult your dealer for advice. TECHNICAL DESCRIPTION The supplier will make available on request such circuit diagrams, component part lists, descriptions, calibration instructions or other information which will assist the USER's appropriately qualified technical personnel to repair those parts of the EQUIPMENT which are classified by the manufacturer as repairable. The use of ACCESSORY equipment not complying with the equivalent safety requirements of this equipment may lead to a reduced level of safety of the resulting system. Consideration relating to the choice shall include: ­ use of the accessory in the PATIENT VICINITY ­ evidence that the safety certification of the ACCESSORY has been performed in accordance to the appropriate EN60601-1 and/or EN60601-1-1 harmonized national standard. The transportation and storage environmental conditions are: Temperature : -20°C - +60°C (-4°F - +140°F) Humidity: 90%RH or less at 40°C (104°F) Atmospheric pressure : 50 kPa - 106 kPa Note : The above transportation environmental conditions indicate the storage environmental conditions during transport. 4 PRODUCT OUTLINE The digital monochrome printer P95DW/P95DE uses the thermal printing system. [. . . ] The indicator displays " " and all the buttons become invalid. · If this error occurs while more than one copy is being printed or there are images waiting to be processed, printing is cancelled at the occurrence of the error. Printing of the interrupted image or all the images saved in the memory that are waiting to be processed is cancelled. 21 11 STATUS AND MODES LED display Contents of LED display Power off During data receiving Remaining number of copies / number of copies 1 to 99 100 to 199 200 Continuous copy printing Set state/Mode Power off Stand-by During data receiving Print state Printer brightness mode Printer contrast mode Printer sharpness mode Function mode Fine adjustment of the picture brightness Fine adjustment of the picture contrast Fine adjustment of the picture sharpness Gamma curve setting Adjustment control lock setting USB iSerial number setting Error detect state No paper Button input error Door is open. Gear lock 22 12 USE OF CLEANING PAPER When the thermal head is dirty with dust, etc. , white spots or stripes may appear on the print. [. . . ]