User manual MITSUBISHI PCFY-NKMU-E

[. . . ] Use the attached RGB cable with this equipment so as to keep interference within the limit of an FCC Class B device. This apparatus must be grounded. When using the projector in Europe: COMPLIANCE NOTICE This Projector complies with the requirements of the EC Directive 2004/108/EC "EMC Directive" and 2006/95/EC "Low Voltage Directive". The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterized by their connection to the public low voltage power supply system. DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE. CAUTION Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75. [. . . ] Select this setting when you want to view images from the front with the projector set at the ceiling. opt. INSTALLATION WALL SCREEN LAMP MODE AUTO POWER ON AUTO POWER OFF IMAGE CAPTURE SPLASH SCREEN BACK COLOR MUTE MODE IMAGE REVERSE BEIGE STANDARD OFF OFF GO ON BLUE BLACK OFF WALL SCREEN ON LAMP MODE LOW AUTO POWER ON ON/OFF AUTO POWER OFF IMAGE CAPTURE SPLASH SCREEN OFF/5-60 min ON/OFF BACK COLOR BLUE/BLACK/IMAGE AV MUTE MODE BLACK/IMAGE OFF MIRROR IMAGE REVERSE INVERT MIRROR INVERT · · · By default, the LAMP MODE is set to STANDARD. The LAMP MODE is set to either STANDARD or LOW depending on the setting last selected, and you cannot switch the LAMP MODE in about one minute after the lamp is on. You cannot select IMAGE CAPTURE SPLASH SCREEN when PASSWORD FUNCTION in the FEATURE menu is set to SPLASH ID SCREEN, as the password lock is activated. When you keep projecting images with BACK COLOR or AV MUTE MODE set to IMAGE for an extended period of time, an afterimage may linger on the screen. EN-18 Menu operation (continued) 3. FEATURE menu Menu option AUTO ASPECT Setting Feature description Automatically sets the aspect ratio in relative to the input signal. Selects a desired screen position for anamorphically squeezed or horizontally compressed images stored on DVD disks. You can select from CENTER, UPPER, and LOWER by pressing the ENTER button. Select this setting when you want to project images in the full screen. Select Auto to automatically activate the film mode when the input video signal is a video signal from a film. Select Auto to automatically set the appropriate video format in relative to the input signal. If projected images aren't displayed correctly, select a desired video format manually. SYNC LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 1 1 AUTO OFF 0 0 0 0 SIGNAL USER menu · · · · · · Horizontal strips may appear in the enlarged projected image, though these conditions are not a malfunction. When you change the value of the horizontal or vertical position drastically, noise may appear. The adjustable range of the vertical position varies depending on the type of the input signal. When you increase the value of OVER SCAN, noise may appear on the screen. You can set the IMAGE, SIGNAL, and SIGNAL-USER menus only when the signal is input. Important: 5. INFORMATION menu Menu option Feature description This menu shows a lamp operating time (hour) calculated assuming that LAMP MODE is LOW. · When the LAMP MODE is STANDARD, this menu shows a longer lamp operating time than the actual time. (See page 26 for the interval of lamp replacement. ) · When the lamp operating time is 0 to 10 hours, "0H" is displayed. When the lamp operating time exceeds 10 hours, the actual hours are displayed. · When the lamp operating time reaches 2250 hours, the bar turns yellow. (The lamp lifetime is 3000 hours. ) Indicates the name of the terminal to which the currently projected video signal is being input. [. . . ] Change with a new lamp if this problem recurs. Steady red Steady red The lamp operation time exceeds the time elapsed until the lamp shutdown. Blinking green/red Off Close the cover correctly. Steady or Blinking green/red Blinking Abnormal. Contact your dealer. EN-30 Specifications Model Rated power supply Rated input Display Technology Colors Projection lens Light source lamp Picture size PC compatibility PCFY-NKMU-E 100 - 240 V AC, 50 / 60 Hz 3. 9 A 0. 55-inch Single chip Digital Micromirror Device (DMD) Pixels 1024 x 768 = 786432 pixels 16770000 colors F 2. 8, f = 7. 7 mm 280 W 40 - 300 inch (aspect ratio 4:3) Resolution:640x400 (Expand) - 1024x768 (Real) - 1280x1024 (Compress) Sync on Green available NTSC / NTSC 4. 43 / PAL (including PAL-M, N) / SECAM, PAL-60 Component Video (DVD/HDTV) (480i, 576i, 480p, 576p, 1080i, 720p) 2 W Mono, Round type ø4. 5 cm x 1 Luminance signal: 1. 0 Vp-p 75 (negative sync. ) Chroma signal: 0. 286 Vp-p 75 (burst signal) 1. 0 Vp-p 75 (negative sync. ) 350 mVrms, 10 k or more RGB: 0. 7 Vp-p 75 (negative sync. ) YPBPR/YCBCR : Y:1. 0 Vp-p (negative sync. ) HD/CS : TTL level (positive or negative) VD : TTL level (positive or negative) Serial terminal (RS-232C) (D-SUB 9-pin) USB terminal (for Page Up/Down) 332 x 102 x 250 mm (width x height x depth) Approx. 3. 3 kg 114 inch (1. 8 m) +41°F (+5°C) - +95°F (+35°C), 30 - 90% Video compatibility Speaker S-video input Video input Audio input Analog RGB input PBPR/CBCR:0. 7 Vp-p Control connector Outside dimensions Weight Length of power cord Temperature, humidity (performance guaranteed) · The specifications and outside appearance of the projector are subject to change without prior notice. EN-31 ENGLISH Type DLPTM DATA projector Specifications (continued) Connectors COMPUTER-IN/OUT (Mini D-SUB 15-pin) 11 15 6 10 1 IN pin No. R(RED)/CR G(GREEN)/Y B(BLUE)/CB GND GND GND GND GND DDC5V GND GND DDC Data HD/CS VD DDC Clock 5 OUT pin No. [. . . ]