User manual MITSUBISHI PD-4225S

[. . . ] Owner's Guide Mitsubishi Plasma TV PD-4225S Technically Anything is Possible® © Copyright 2003, Mitsubishi Digital Electronics America Warning Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electric Code (U. S. A. ). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] The TV Component Ports Y Y Y Y Y PB PR DVD Player Video Output Ports Pr Pb B-Y R-Y Cb Cr PB PR DTV Setup - To watch digitally broadcasted programs, purchase and connect a digital set-top box. - This TV supports HDCP (High-bandwidth Digital Content Protection) protocol for DTV (480p, 720p, 1080i) modes. (FACTORY INSTALLED) How to connect 1. Use the TV's COMPONENT (Y, PB, PR) INPUT, RGB, or MONITORLINK/DVI jack for video connections, depending on your set-top box connector. Use the DEVICE button on the remote control to select Component, RGB or MonitorLink. or Digital Set-top box or Owner's Manual 25 NOTE: Not all cables shown are included with the TV. They are available at most consumer electronics stores. Monitor Out Setup The TV has a special signal output capability which allows you to hook up a second TV or monitor. See the Operating Manual of the second TV or monitor for further details regarding that device's input settings. NOTE: · Component, RGB-PC/DTV 480p/720p/1080i, S-video input sources cannot be used for Monitor out. PC Setup - This TV provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The TV sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel (DDC) protocol. How to connect 1. To get the best picture quality, adjust the PC graphics card to a 640x480, 60Hz setting. If using a sound card, adjust the PC sound as required. How to use 1. Turn on the TV by pressing the POWER button on the TV's remote control. There may be noise in the PC mode associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not be changed, change the PC graphics card or consult the manufacturer of the PC graphics card. NOTES: · The MonitorLink Input is not intended for use with personal computers or devices generating video signals with computers. · Avoid keeping a fixed image on the TV's screen for a long period of time. · The synchronization input form for Horizontal and Vertical frequencies is separate. FACTORY INSTALLED CABLE 26 Plasma TV NOTE: Not all cables shown are included with the TV. They are available at most consumer electronics stores. HD-5000/MONITORLINK SETUP HD-5000/MONITORLINK 1. Connect a MonitorLink/DVI cable from the TV back panel to the Mitsubishi HD Receiver/Controller back panel. Connect the MonitorLink Control/RS-232 cable from the TV back panel to the Mitsubishi HD Receiver/Controller back panel. By using a Stereo Mini-plug to L and R RCA adapter, connect the L (left) and R (right) audio cables from the HD-5000 receiver/controller to the Audio Input Mini-plug on the back of the TV. NOTES: · The 29-pin MonitorLink/DVI and 9-pin RS-232 cables can be found at your local electronics store. [. . . ] Warranty service will be provided in your home or, if required, at an authorized MITSUBISHI service center, provided that your television is located within the geographic territory customarily covered by an authorized MITSUBISHI service center. If not, you must either deliver your television to an authorized service location at your own expense, or pay for any travel and/or transportation costs the service center may charge to and from your home. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service. Present your sales receipt or other document which establishes proof and date of purchase. [. . . ]