User manual MITSUBISHI PEFY-P18

[. . . ] DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE. CAUTION Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment, ANSI/NFPA 75. When using the projector in Europe: COMPLIANCE NOTICE This Projector complies with the requirements of the EC Directive 89/336/EEC "EMC Directive" as amended by Directive 92/31/EEC and 93/68/EEC, and 2006/95/ EC "Low Voltage Directive". The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. [. . . ] · Cover the lens with the lens cap to protect it from dust. AUTO POSITION button When the image supplied from the computer is displaced, carry out the following procedure. Display a bright image (such as a full-screen display of the Recycle Bin window). The projector automatically makes optimum positional settings for the input signal. · If the image is not projected in the correct position even after you press the AUTO POSITION button several times, change the settings in the SIGNAL menu to put the image in the correct position. (See page 33. ) · When you carry out this procedure with a dark image, the image may be displaced. When connecting to a notebook computer: When the projector is connected to a notebook computer, images may not be projected in some cases. In such cases, set the computer so that it can output signals externally. Example of the setting procedure for external output Press the [Fn] key and any of the keys [F1] to [F12] at the same time. (The key to be pressed depends on the type of the computer you use. ) EN-23 Menu operation · Menus are not displayed when no signal is supplied to the projector. IMAGE GAMMA MODE AUTO, SPORTS, VIDEO, CINEMA USER1 REFERENCE SPORTS, VIDEO, CINEMA USER2 ADJUST MODE ALL, RED, GREEN, BLUE ±30 HIGH ±10(R) ±10(G) ±10(B) ±30 MID ±10(R) ±10(G) ±10(B) HIGH BRIGHTNESS LOW ±10(R) ±10(G) ±10(B) COOL CONTRAST R ±60 MEDIUM CONTRAST G ±60 WARM CONTRAST B ±60 USER BRIGHTNESS R ±60 ±10 BRIGHTNESS G ±60 ±10 BRIGHTNESS B ±60 ±5 VERTICAL LOCATION ±26 OK AV MEMORY1 AUTO IRIS AUTO IRIS 1, AUTO IRIS 2, AUTO IRIS 3, OPEN AV MEMORY2 AV MEMORY3 NOISE REDUCTION *1 CTI *1 INPUT LEVEL ON , OFF 0-5 ±5 (for analog signal input) ENHANCED/NORMAL (for digital signal input) CONTRAST BRIGHTNESS COLOR TEMP. COLOR TINT SHARPNESS *1 ADVANCED MENU AV MEMORY SAVE INSTALLATION LAMP MODE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN BACK COLOR IMAGE REVERSE TRIGGER OUT TEST PATTERN LENS LOCK ASPECT PASSWORD FUNCTION MENU POSITION MENU DIMMER CINEMA MODE *2 VIDEO SIGNAL *3 SETUP *1 SCART INPUT *8 LANGUAGE RESET ALL HORIZ. POSITION*6 VERT. POSITION *6 FINE SYNC. *5, *6 TRACKING *1, *5, *6 COMPUTER INPUT *5 OVER SCAN HOLD *5, *6 USER STANDARD, LOW ON , OFF OFF, 5, 10, 15, 30, 60min ON , OFF BLUE, BLACK OFF, MIRROR, INVERT, MIRROR INVERT ON , OFF ZOOM/FOCUS LOCK CROSS HATCH LENS SHIFT LOCK OK LENS SHIFT RESET ON, OFF ON, OFF OK FEATURE AUTO, 4:3, 16:9, ZOOM1, ZOOM2, STRETCH *4 OK DISPLAY INPUT , MENU ACCESS LOCK OK 1 (Upper left), 2(Lower right) UNLOCK ON, OFF AUTO , VIDEO, FILM AUTO , NTSC , PAL , SECAM, 4. 43NTSC, PAL-M, PAL-N, PAL-60 AUTO, OFF, 3. 75%, 7. 5% ON, OFF , English, Español, Deutsch, Français, Italiano, , , OK 0 - 999 *4 0 - 999 *4 0 - 31 0 - 9999 *4 AUTO, RGB, YCBCR / YPBPR 100 - 90% *4 OFF BEGIN ON END OK CLAMP POSITION *5, *6 CLAMP WIDTH *5, *6 VERT. SYNC LPF *6, *7 SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) , PORTUGUÊS SIGNAL INFORMATION LAMP TIME(LOW) INPUT RESOLUTION VERTICAL FREQUENCY HORIZONTAL FREQUENCY SYNC. TYPE *5, *6 0 - 99 0 - 99 1- 255 1- 63 AUTO, OFF ON, OFF 0 - 32 0 - 32 0 - 95 0 - 95 *4 *4 * 1: * 2: * 3: * 4: * 5: * 6: * 7: * 8: * 9: Not available with certain signals. Available only when the input signal is TV50, TV60, 480i, 576i or 1080i. Available only when the input signal is from the VIDEO IN or S-VIDEO IN terminal. (See page 29. ) AV MEMORY SAVE · By using the AV memory function, you can save up to 3 setting patterns of IMAGE menu for each input terminal. (See page 29. ) · INPUT LEVEL is unavailable when the digital signal is supplied from the YCBCR/YPBPR terminal of the connected device. EN-25 Menu operation (continued) 2. INSTALLATION menu opt. INSTALLATION LAMP MODE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN BACK COLOR IMAGE REVERSE TRIGGER OUT TEST PATTERN LENS LOCK AV MEMORY 1 STANDARD OFF OFF ON BLUE OFF OFF CROSS HATCH OK ON 2. INSTALLATION menu ITEM LAMP MODE SETTING STANDARD LOW ON / OFF FUNCTION Select this option when you want to view images in a well-lit room. The fan operating sound is reduced and the lamp lifetime becomes longer. When ON is chosen, the lamp is automatically lit when the power cord is plugged in the wall outlet. Use to set the time elapsed before the projector enters the stand-by mode when there is no signal input from the source. Use to change the color of the screen that appears when no signal is supplied. Select when viewing images from the front with the projector installed on the floor. Select when viewing images projected from the behind of the screen with the projector installed on the floor. Select when viewing images projected from the behind of the screen with the projector installed on the ceiling. [. . . ] Important: · Some computers aren't compatible with the projector. · The projector's maximum resolution is 1920 x 1080 pixels. It may not display images of higher resolutions than 1920 x 1080 correctly. · If the resolution and frequency of your computer aren't shown on the table, find the compatible resolution and frequency by changing the resolution of your computer. · This projector doesn't support 480p signals from video devices having 4 lines (R, G, B, CS*) or having 5 lines (R, G, B, H, V). [. . . ]